Technical Education And Training Department

Technical Education And Training Department has published Supply Testing Installation Commissioning And Demonstration Of Hand Tools Instruments Equipment And Machineries Of Electrician And Turner Trade At Iti Jalpaiguri , Supply Of Short Fall Of Electrician Trade Course , Relay- Reverse Current, 16A, 440V , Relay- Over Current, 16A, 440V , Relay-Under Voltage, 360V-440V , Pin Type Insulators Including Hardware Fitting , Shackle Type Insulators Including Hardware Fitting , Egg Type Insulators Including Hardware Fitting , Suspension Type Insulators Including Hardware Fitting , Laboratory Type Induction Coil, 1000 W , Knife Switch Dpdt Fitted With Fuse Terminals, 16 Amp , Knife Switch Tpdt Fitted With Fuse Terminals, 16 Amp/ 440 V , Earth Plate, 60Cm X 60Cm X 3.15Mm Copper Plate , Earth Electrode,Primaryelectrode2100x28x3.25Mm Secondary Cu Strip 20X5mm , Mccb, 100Amps, Triple Pole , Twisted Pair Cable, 1 Mtr , Non-Metallic Sheathed Cable , 1 Mtr , Underground Feeder Cable , 1 Mtr , Ribbon Cable , 1 Mtr , Metallic Sheathed Cable, 1 Mtr , Multi-Conductor Cable, 1 Mtr , Coaxial Cable , 1 Mtr , Direct-Buried Cable, 1 Mtr , Rheostat(Sliding Type), 0-25Ohm,2Amp , Rheostat(Sliding Type), 0- 300Ohm, 2 Amp , Rheostat(Sliding Type), 0-1Ohm, 10Amp , Rheostat(Sliding Type), 0-10Ohm,5Amp , Bus Bar With Brackets, 1 Mtr Each , Rcc Pole With Accessories (Ms Angle Iron, ‘C’ Clamp, Stay Insulator Etc.) And Materials, 6 Mtrs , Digital Multi Meter, Dc 200Mv -1000V,0 – 10A & Ac 200Mv- 750V , 0-10A, Resistance 0-20 M? And 3 1/2 Digit , Digital Wattmeter, 230 V, 1 Kw, 50 Hz , Magnetic Flux Meter, 0-500 Tesla , Meggar, Analog-500V , Ac Starters:- Resistance Type Starter, For A.C Motors Of 2 To 5 H.P. , Ac Starters:- Star Delta Starter–Semi Automatic, For A.C Motors Of 2 To 5 H.P. , Ac Starters:- Star Delta Starter- Soft Starter, For A.C Motors Of 2 To 5 H.P. , Oscilloscope Dual Trace, 20 Mhz , Temperature Controlled Soldering Iron, 50-Watt, 230 Volt , Immersion Heater,1500Watt,240V , Motor Pump Set,1Hp,1Phase,240V , Oil Testing Kit, Oil Testing Kit, 230V,Singlephase50 Hz 60 Va Output 0-60 Kv Variable , Inverter With Battery, 1 Kva With 12 V Battery Input- 12 Volt Dc, Output- 220 Volt Ac , Dc Power Supply, 0 - 30 V, 5 A , Potential Transformer,415V,50Hz,Ptratio,440V/110V, 10 Va , Ac Phase-Wound Slip Ring Motor With Starter Switch, 5Hp,440V,3Phase,50Hz , Universal Motor With Starter/Switch, 240V,50Hz,1 Hp , Three Phase Transformer, Shell Type Oil Cooled With Delta/ Star, 3 Kva , 415/240 V, 50 Hz , Diesel Generator Set With Change Over Switch, Over Current Breaker And Water/ Air-Cooled With Armature, Star-Delta Connections Ac 3 Phase ,7.5 Kva, 415 Volt Or Higher Rating , Used Dc Generators-Series Type For Overhauling Practice , Used Dc Generators- Shunt Type For Overhauling Practice , Used Dc Generators -Compound Type For Overhauling Practice , Ceiling Fan Coil Winding Machine, 250V, 50 Hz, 1-?, With Speed Control , Shaded Pole Motor, Fractional Hp, 240V,50 Hz , Smart Meter,1Phase-Smart Energy Meter , Smart Meter,3Phase-Smartenergymeter , Ev Charger, 3Phase Input , Ev Charger (Home), 1Phase Input , Supply Of Short Fall For Turner Trade Course , Surface Plate - Granite, 1000 X 1000 Mm With Stand And Cover , Marking Table (Ci), 120 X 120 Cm With Stand And Cover , Micrometer Inside, Upto 25 To 50 Mm, Least Count 0.01 Mm With Nabl Accrediated Lab Certificate , Vernier Caliper Outside, Inside And Depth, 200Mm / 8 Inch With Metric And Inch Scale (Lc=0.02Mm) With Nabl Accrediated Lab Certificate , Dial Vernier Caliper, 200Mm , Least Count 0.05Mm With Nabl Accrediated Lab Certificate , Vernier Bevel Protractor, 300Mm Blade With Nabl Accrediated Lab Certificate , Vernier Micrometer, 0- 25 Mm O/S Lc=0.001Mm With Nabl Accrediated Lab Certificate , Gauge Feeler, Thickness - 0.05Mm To 0.3 Mm By 0.05 Mm-13 Leaves , Gauge Feeler, Thickness -0.4Mm To 1Mm By 0.1Mm -13 Leaves , Gauge - Radius Set, 1Mm To 25Mm By 0.5Mm , Drill Angle Gauge, 45 Degree, 55 Degree, 90 Degree , Magnifying Glass, 75Mm With Magnifying Factor 10X , Plain Ringgauge, 12,16,20,25,30,32,36,40,45,50 Mm , Plainplug Gauge, 12,16,20,25,30,32,36,40,45,50 Mm , Tap &Die , Ba No 0 To 10 In A Box , Tap &Die Set, Metric - 3 To 24 Mm , Tap &Die , Bsf Upto 1 Inch , Tap &Die, Bsw Upto 1 Inch , Angle Plate, Adjustable - 150 X 175 X 250 Mm , Tool Makers Button , Hand Chaser With Handle, M-12 & M-16 (External) , Hand Chaser With Handle, M-12 & M-16 (Internal). Last date of submission for this tender is 2025-01-20. This is a Tool Kit tender in Jalpaiguri, West Bengal