Technical Education And Training Department

Technical Education And Training Department has published SUPPLY, INSTALLATION AND DEMONSTRATION OF DIFFERENT MACHINERIES, EQUIPMENTS, INSTRUMENTS, TRAINER KITS, MODELS, STUDY SETUPS ETC.FOR WORKSHOPS AND LABORATORIES- 1 Cut section model of 4 stroke SI Engine (Metal Body) 2 Tools & Special Tools used for Dismantling and assembling the Engine and Automobile. 2 Set of each Tools & Special Tools 3 Petrol Engine (Multi cylinder carburetor SI and Multi cylinder MPFI SI engine) 4 Diesel Engine (Single Cylinder FIP CI Engine and Multi cylinder CRDI CI Engine) 5 A small car (petrol - Engine fitted with AC and ECU system) 6 Engine Radiator 7 Thermostat valve, wax pellet & Bellows type 8 Carburettor 9 A complete truck chassis 10 CRDI AC Drive Common Rail Injector Test Bench 11 Engine Test Setup with OPEN ECU 12 Workplace Safety gears For Automotive Repair 13 Actual model of front dead axle with stub axle 14 Actual model of front axle 15 Various type of Rear axle 16 Complete actual working set up of steering system of a vehicle fitted with tilt and telescoping and collapsible steering column 17 Optical wheel alignment machine 18 Complete working set -up of power steering (hydraulic type) system 19 Actual cut section of power steering of a vehicle with cut section of re - circulating ball bearing. 20 Independent Suspension systems of Automobile 21 Anti lock braking system, (Working Model) 22 Telescopic shock absorber, (Single acting & double acting) 23 Actual working single plate dry type clutch assembly 24 Actual working multi - plate clutch assembly 25 Actual working differential with rear axle assembly 26 Actual cut section of transaxle fitted with fluid coupling/ torque converter 27 12 V Automotive Battery with Battery charger 28 Hydrometer 29 Battery Load Test equipment 30 Actual working Battery ignition system circuit of an Automobile. 31 Starter motor with bendix drive. 32 Cut section model of starting circuit 33 No load test equipment for starter motor. 34 Different types of electronic ignition system 35 Actual working Horn circuit. 36 Actual working Charging System Circuit. 37 Actual working Lighting System circuit of Automobile 38 Ignition timing of a multi-cylinder engine with a strobe (Neon Light) equipment (12V system) 39 Complete wiring circuit of a two wheeler and four wheeler 40 Cylinder bore dial gauge 41 Cylinder Boring machine 42 Fuel injector tester, (Diesel) 43 Actual working Differential assembly 44 Wheel Balancing Machine 45 Brinell Hardness Testing Machine 46 Model of Thermal Power- plant 47 Cut Section Model of Boiler Mountings set 48 Cut Section Model of Boiler Accessories set 49 Experimental Set-up for Determination of Thermal Conductivity of solid metal steel rod 50 Model of Reverted Gear- train 51 Reciprocating Pump Test Rig 52 Bench Grinding Machine with all accessories 53 MIG Welding Machine with all accessories and Gas cylinder 54 TIG Welding Machine with all accessories Gas cylinder 55 Slip Gauge (Metric Set) 56 Plain Milling Cutter (Different size) 57 Slitting Saw 58 Radial Drilling Machine 59 Pillar Drilling Machine 60 Vertical End Mill Cutter 61 T-slot Cutter for Milling 62 Angular Cutter for Milling (30 deg angle) 63 4 Double angle Milling Cutter for Milling (60 deg) 64 Gear Cutter for Milling 65 Form Milling Cutter 66 Bench Drilling Machine 67 Milling Machine Attachments (Universal Dividing Head) 68 Single Phase Autotransformer with Tap Changing 69 Pulse Transformer 70 Isolation Transformer 71 Different Class Turn off Circuits of SCR Sets of each type 72 Complete Set up of Solar PV Cell, Battery and Charge controller Unit & CFL 73 Model of Concentrated Solar Power Plant 74 Model of Horizontal axis Wind turbine Power Plant 75 Model of Verical axis Wind turbine Power Plant 76 Pyranometer to measure the Solar Radiation 77 Complete Set up to measure Open circuit Voltage ratio test of Slip-ring Induction Motor 78 Complete Set up to determine the efficiency and speed regulation for different loads in a Single phase Induction Motor 79 Speed reversing facility of AC Servo Motor 80 Speed reversing facility of DC Servo Motor 81 Contact type Tachometer with different type of contact arrangement 82 DC Ammeter(0-1000mA)(Analog type) 83 Complete Set up of Programmable Logic Controller . Last date of submission for this tender is 2025-01-24. This is a Dismantling Work tender in Ranaghat, West Bengal