Uttarakhand Power Corporation Limited

Uttarakhand Power Corporation Limited has published Tender For Replacement Of Existing Weasel/ Rabbit Conductor By Aaac Al-59, 99 Sq. Mm Covered Conductor Of 11 Kv Horawala Feeder, Emanating From 33/11 Kv Sub-Station Rudrapur Under Edsd, Herbertpur Under Edd, Vikasnagar-- 1 Material 2 PP Clamp with N&B SP-33 3 PP Clamp with N&B SP-55 4 IPC with Aluminium Bail for Earthing 1 No. 5 11 KV Suspension Ties/Cable Ties on every Pin Insulator 6 11 KV IPC for CC to CC Connection in every Section Pole 7 11 KV IPC for CC to Bare Connection at both end and tapping 8 11 KV Mid Span Jointing Kit at every 500 mt. Cable Drum 9 Supply of 11 KV AAAC AL 59 Equivlent to 99 sqmm Covered Conductor Equivalent to 300 Amp. 10 11 KV 90 KN Tension Clamp with Bail and IPC 11 Labour 12 Fabrication of M.S. Channel & Angle 13 Excavation of Earth for Pole Pit of Size 0.9x0.6x1/6 of Full Length of Pole for Erection of Pole in all type of Soil including Proper Dressing of Sides and Ramming of Bottom including getting out the Excavated Soil and Disposal of Surplus Excavated Soil as directed, Complete Work 14 Erection of following Single Support Pole in Proper Level and Alignment alongwith Fixing of all Accessories STP SP 33 15 Erection of following Single Support Pole in Proper Level and Alignment alongwith Fixing of all AccessoriesSTP SP 55 16 Grouting of Pole in Size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement :4 graded stone 20mm nominal size : 8 coarse sand) Block including Cost of Cement, Sand and Stone Ballast Back Filling of Soil and Boulders in Pit and Ramming and Proper Alignment, Leveling as per RESSPO Construction Manual 17 Muffing of Poles Size 0.45cmx0.60cm radious with CC 1:3:6 (1 cement : 3 coarsend : 6 graded stone 10mm nominal size) Block Size 45 cm Height from Ground Level including cost of Cement, Sand & Stone etc. 18 Making Of section Poles 19 Cartage of following Poles from Store Centre to Nearest Road Site with Loading/Unloading at both points & proper staking (Loading, Unloading & Carriage per pole) (21-50 Km.)ST Pole SP 33 20 Cartage of following Poles from Store Centre to Nearest Road Site with Loading/Unloading at both points & proper staking (Loading, Unloading & Carriage per pole) (21-50 Km.)ST Pole SP 55 21 Cartage of Other Material by Vehicle from Store Centre to Nearest Road Site with Loading/Unloading at both points (21-50 Km.) 22 Head Load Cartage of following Poles from Road Site to Construction Site (Rates are per Pole/Km, including Loading/Unloading at both points) (0-1 Km.) ST Pole SP 33 23 Head Load Cartage of following Poles from Road Site to Construction Site (Rates are per Pole/Km, including Loading/Unloading at both points) (0-1 Km.) ST Pole SP 55 24 Head Load Cartage of Small Material by Vehicle from Store Centre to Nearest Road Site including Loading & Unloading at both points (0-1 Km.) 25 Fixing of IPC with Al. Bail for Earthing 26 Jumpering of D/P TPMO fuse set and T/F 27 Proper Alignment of Tilted Pole 28 Fixing of 11 KV 90 KN Tension Clamp with Bail and IPC 29 Fixing of 11 KV Suspension Ties/Cable Ties on every Pin Insulator 30 Fixing of 11 KV Mid Span Jointing Kit at every 500 mt. Cable Drum 31 Fixing of 11 KV IPC for CC to CC Connection in every Section Pole 32 Fixing of 11 KV IPC for CC to Bare Connection at both end and tapping 33 Laying, Spreading, Stringing and Sagging of 11 KV Line in 3 Phase of the following Wire as Phase Wire including Proper Sagging with Binding and Jumpering as per user Manual and Sagging Chart (inclusive of cartage and head load Cartage at work site). Rollers of the appropriate diameter and quantity have to be provided for installation. The roller shall have a smooth clean surface, no sharp edges and shall rotate easily to prevent the covering from damage any abrasive contact with soil or stone is not permitted, abrasive contact of the covering with branches or similar shall be avoided. Covered conductor shall be pulled by using appropriate pulling devices ensuring that the pulling force is distributed to the conductor recommendation given in EN-50397-3 should be followed for storage transport and installation of covered conductor. 34 Removing of Old Rabbit/Weasel Conductor with Opening of Existing, Jumpering and Making of Bundle with Carriage from Pit Site to Store including Loading/Unloading, Complete Work (Rabbit/Wesal Conductor) 35 Carriage of Rabbit/Wesal Conductor Scarp Site to Store 36 Looping & Chooping of Tree Branches of Route Clearance 37 Painting of Pole 38 Fixing of Aluminium Lugs . Last date of submission for this tender is 2024-10-24. This is a Abrasive and Abrasive media tender in Dehradun, Uttarakhand