Ministry Of Micro Small And Meduim Enterprises

Ministry Of Micro Small And Meduim Enterprises has published Purchase Of Hand Tools And Measuring Instruments Hand Tools And Measuring Instruments - Cutting Tools:- 01 Flat File 6 Inch Single Cut. 02 Flat File 6 Inch Double Cut. 03 Square File 6 Inch Double Cut. 04 Triangular File 6 Inch Double Cut. 05 Round File 6 Inch Double Cut. 06 Half Round File 6 Inch Double Cut. 07 Knife Edge File 6 Inch Double Cut 08 Warding File 6 Inch Single Cut 09 Flat File 10 Inch Bastard Single Cut. 10 Flat File 10 Inch Bastard Double Cut. 11 Square File 10 Inch Bastard Double Cut. 12 Triangular File 10 Inch Bastard Double Cut. 13 Round File 10 Inch Bastard Double Cut. 14 Half Round File 10 Inch Double Cut. 15 Needle File Set B. Chisel:- Sl.No. Name 01 Cold Chisel Flat 10Cm 02 Cold Chisel 10 Inch 03 Cold Chisel 10Inch Cross Cut 04 Cold Chisel 10Inch Round Nose 05 Hot Chisel Flat 10 Inch 06 Hot Chisel 10 Inch Cross Cut 07 Hot Chisel 10 Inch Flat 08 Cow Mouth Chisel 8 Inch 09 Diamond Cut Chisel 10 Inch C. Hacksaw:- Sl.No. Name 01 Hacksaw Frame Fixed 12 Inch 02 Hacksaw Frame Adjustable 03 Hacksaw Frame Deep Cut D. Drills:- Sl.No. Name 01 Twist Drill Straight Shank 1 To 12 Mm In 0.5 Mm Steps 02 Taper Shank Drill 12 – 24 Mm In 1.0 Mm Steps E. Taps:- Sl.No. Name 01 Tap Set 2 - 14 Mm 02 Tap Set ¼ To 1 / 8, 3 / 16, 5 / 8, 1 / 2, 1 Inch Die:- Scraper:- Spanner - Measuring Instruments:- 01 Vernier Caliper 0-150 Mm. ( L.C 0.02 Mm ) 02 Dial Vernier Caliper 0-200 Mm ( L.C 0.005 Mm ) 03 Digital Vernier Caliper 0-150 Mm. ( L.C 0.001 Mm ) 04 Vernier Depth Gauge 0-150 Mm ( L.C 0.02 Mm ) 05 Vernier Height Gauges 300 Mm ( L.C 0.02 Mm ) 06 Vernier Bevel Or Angle Protractor 07 Micrometer Outside 0-25, 25-50, 50-75, 75-100 Mm 08 Micrometer Inside 0-25, 25-50, 50-75, 75-100 Mm 09 Micrometer Inside ( Three Point ) 0-25, 25-50, 50-75Mm. ( L.C. 0.001Mm ) 10 Digital Micrometer Outside 0-25 Mm. ( L.C. 0.001Mm ) 11 Depth Micrometer 0-25 Mm. ( L.C. 0.001Mm ) 12 Tool Maker Microscope 0-150 Mm 13 Try Square 18Cm Blade 14 Jenny Caliper Inside Spring Loaded 10 Cm 15 Jenny Caliper Outside Spring Loaded 10 Cm 16 Divider Spring Loaded 10 Cm 17 Steel Scale 0-150, 0-300 Mm 18 S.W.G. ( Standard Wire Gauge ) 19 Engineer Try Square Blade 50, 75, 100 Mm 20 Dial Indicator 0.001 Mm With Magnetic Stand 21 Puppy Test 1Μ & 2Μ 22 V-Block Pair 7 Cm And 15 Cm With Clamps 23 Slip Gauge Set Metric Workshop Grade 24 Filler Gauge 25 Radius Gauge ( 1-7.5, 7.5-15 Mm ) 26 Thread Pitch Gauge ( Metric & Inch ) 27 Snap Gauge Go And Not Go 10-30 Mm In Step 1Mm 28 Plug Gauge 5 - 30 In Step Of 1 Mm 29 Hole Gauge 30 Pin Gauge 1 Set Form 1Mm Onward 31 Spirit Level 10 Inch Metal 32 Sin Bar 200 Mm 33 Straight Edge 45 Cm Steel 34. Height Gauge 0 To 75Cm Sl.No. Name 01 Scribers - Straight & Bend 8 Inch 02 Dot Punch 03 Center Punch 04 Letter Punch 3 Inch Set 05 Prick Punch 06 Number Punch 3 Inch Set 07 Leg Vice 5 Inch 08 Carpenter Vice 4 Inch 09 Pipe Vice 4 Inch 10 Pin Vice 11 Tong 12 Sniper ( Scissor ) 4 – 10 Inch 13 C” Clamp 150 - 300 Mm D. Striking Tools:- Sl.No. Name 01 Ball Peen Hammer 100-150Gm With Handle 02 Cross Peen Hammer 100-150Gm With 03 Straight Peen Hammer 100-150Gm With 04 Flat Hammer 100-150Gm With Handle 05 Claw Hammer With Handle 06 Nylon Hammer 07 Leather Hammer 08 Wooden Hammer 09 Rubber Hammer E. Surface Plate, Anvil, Angle Block& Table Etc. :- Sl.No. Name 01 Anvil 20 Kg 02 Anvil Stand 03 Cast Iron Surface Plate 45 X 45 Cm 04 Graphite Surface Plate 45 X 45 Cm 05 Marking Table 91 X 91 X 122 Cm 06 Angle Plate 10 X 20 Cm 07 Surface Roughness Comparison Plates N1-N12 Grade 08 Wooden Bench For Bench Vice 6Ft X 3Ft X 3.5 Ft ( Height ) With 5” Vice 05 Nos. Fitted In Bench 09 Taper Sleeve Morse Taper No 1-2, 2-3 , 3-4, 4-5 F. Cleaning & Safty:- Sl.No. Name 01 Paint Brush 4 Inch 02 Safety Goggle 03 Safety Gloves 04 File Cleaning Brush G. Cutting Tools:- Sl.No. Name 01 Lathe Tools H.S.S.1 / 2 X 1 / 2 X 4 Inch 02 Diamond Dresser With Stand 03 Hss Tool Bit 1X1x6 Inch 04. Side And Face Cutter 80X20x27, 80X6x22, 80X16x27, 100X10x27 Shell End Milling Cutter 63X40x27, 40X32x20, 80X40x27 05. Blade Size 400X32 06 Angular Milling Cutter Angular-105X18x27x30o, 80X20x27x60o, 80X20x27x90o 07 End Mill Cutter5, 10, 15, 20, 08 Grinding Wheel ( For Surface Grinding Machine ) 51A 46H5v8 ( 200X15x31.75 ) H. Other Tools:- Sl.No. Name 01 Nose Plier 200 Mm 02 Combination Pliers 15 Cm 03 Allen Key Set ( Mm & Inch ) 04 Screw Driver Set. Last date of submission for this tender is 2020-02-15. This is a Tool Kit tender in Electronics Service And Training Centre Ramnagar, Uttarakhand