Rural Engineering Department

Rural Engineering Department has published Tender For Construction Of 20.00M X 12.50M Shed With Platform In Collectrate Campus Auraiya - Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. 2.6.1 All kinds of soil 2 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 3 Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. 4 Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer in-charge. (Old CC paver blocks shall be supplied by the department free of cost). 5 Supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. 6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) 7 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work;usingcoarse aggregate and fine aggregate derived from natural sources,Portland Pozzolana Ordinary Portland /Portland Slagcement,admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability andworkabilitywithout impairing strength; including pumping of concrete to site of laying, curing,carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge;for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementConcrete of M25 grade withminimum cement content of 330 kg /cum 8 All work up to plinth level 9 a) Footing 10 Same as item no 4 but all work above plinth & up to floor Vlevel Concrete of M25 grade with minimum cement content of 330kg/cum 11 b/c) Beam & Column 12 Centering and shuttering including strutting, propping etc. and removal of form for 13 Foundations, footings, bases of columns, etc. for mass concrete 14 Lintels, beams, plinth beams, girders, bressumers and cantilevers 15 Columns, Pillars, Piers, Abutments, Posts and Struts 16 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more 17 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate 18 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 19 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 20 Ridges plane (500to600 mm) 21 Wiring points for light with 1.00 mm² F.R. PVC insulated multistrained single core cu conductor cable in PVC conduit with 1.5 mm² FR PVC insulated multistrained cu conductor cable as earth wire down inside the conduit. (131-C) 22 Wiring points for fan with 1.00 mm² F.R. PVC insulated multistrained single core cu conductor cable as earth wire drown inside the conduit. (139-C) 23 Wiring points for plug point with 1.00 mm² F.R. PVC insulated multistrained single core cu conductor cable in PVC conduit with 1.5mm² FR PVC insulated multistrained cu conductor cable as earth wire drown inside the conduit.(134-C) 24 Supply and fixing of power plug with 15A/250w flush type switch and 5 pin 15A/250w flusch type universal socket in suitable MS box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer.(1139) 25 Supply and wiring of Submain with 2 nos. 2.5 mm² cu conductor cable multistrained single core in 20mm² dia PVC conduit with 1 nos. 1.5mm² cu cable as earth wire.(1304-C) 26 Same as above but 2nos. 4 mm² cu conductor cable with 2.5mm² cu cable as earth wire.(216-C) 27 Same as above but 2nos. 16 mm² cu conductor cable with 10mm² cu cable as earth wire in 32mm² dia pipe.(219-C) 28 Supply and wiring of Submain with 4nos. 25 mm² cu FRPVC insulated multistrained single core cu conductor cable with 2nos. 10SWG copper earth continuity wire in 50mm dia rigit steel conduit.(275-B) 29 Supply and fixing surface/flush mounting 12 way SPN distribution box (legrand lexic) with additional metal door.(1025-A) 30 Supply and fixing 6A to 32A SPMCB (10KA) (Legrand lexic) (1002-A) 31 Supply and fixing 63Amp DP isolator (Legrand lexic)(1005-A) 32 Supply and fixing of 2 nos. 8 SWG cu wire in 15mm dia GI pipe for earthing laid in ground or in wall (724) 33 Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 30Watt. to 40 Watt. Confirming to IP 66 protection complete in all respect.1420 CAT AA 34 Supply and fixing of LED Street light Fitting havingdie cast aluminium body and diffuser with driver set suitable for 140 to 150 Watt. Confirming to IP 66 Protection complete in all respects1425 CAT AA 35 Supply and fixing of double light wall bracket fixed on matching MDFED board base etc. Cat.-A (414) 36 Supply and fixing 110 mm dia PVC pipe for rain water 37 Supply and fixing of 50 mm diaGI pipe. 38 Supply and fixing Extension road 16 mm dia for fan 39 Supply & fixingfan as per required engineer incharge . Last date of submission for this tender is 2025-10-07. This is a Shed Construction tender in Auraiya, Uttar Pradesh