Public Works Department

Public Works Department has published Tender For Road safety work at the intersection on Etawah Kachauraghat (A.D.M.) road. - Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 400-2. 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405. 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical Specification Clause 405. 4 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type C as per Technical Specification Clause 508. 5 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C, as per Technical Specification Clause 510 6 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carries of mixed material by tipper to site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density. 7 Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous /granular surface cleaned with mechanical broom. 8 Providing and laying Dense Graded Bituminous Macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 4.00 % by weight of total mix and fille, transporting the hot mix to work site laying with a hydrostatic paver finisher with machenical control to the required grade, level and alingment, rolling with smooth wheeled bibratory and tendom rollers to achiev the desired compection as per MORTH specifiaction clause 507 complete all respects. 9 Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous /granular surface cleaned with mechanical broom. 10 Providing and laying Bituminous Concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder CRMB-55 @ 5.4% ofmix and filler, transporting the hot mix to work site laying with a hydrostatic paver finisher with mechanical control to the required grade, level and alingment, rolling with smooth wheeled bibratory and tendom rollers to achiev the desired compection as per MORTH specifiaction clause 509 complete all respects. 11 RCC Grade M20 using batching plant transit mixer & Concrete pump. 12 Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. 13 Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. As per S.O.R. 1 Ch. Trafic Sign. 14 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67-2012 made of high intensity greade sheeting wide clause 801.3 friced over aluminium sheeting Type-IV 1.5mm thick supprorted on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian condition as per IRC 67-2012 & proof of the same in form of government report shall be uploaded while quoting tender. 15 The Solar cateye shall be produced from an engineered polymer selected for superior impact resisitance and weather-ability. The top of the marker should be transparent for solar charging and light output in active mode. The base of the body shall be yellow or neutral white as approved by Engineer-in-charge, The marker shall incorporate a solar panel(comprising of solar cells) for converting solar energy into electricity, a storage device for storing the energy. LEDs for illumination and a design for providing 360 degree uniform smooth illumination through light tube. The marker shall also have high reflective plastic lenses for conspicuity in passive mode and dual shanks for improved road presence. These markers are intended for application directly onto pavment furfaces and shall be applied with epoxy resin adhesives designed for use with raised pavment markers and as supplied by the marker manufacturer separetely. The solar cateye shall be of height 65+ 2mm & maximum diameter. 136 + 4mm. The solar stud/cateye shall be tested for water ingress as per IP 65 standards & Ip 68 standard & compressvie strength of 13635 Kg tested in accordance with ASTM D4280 and test report shall be submittedat the time of bidding of tender. If somegow tender pre qualification condition do not ask for geovenment report then the report shall be submitted to engineer-in-charge before finalization of bill. The rate shall include all materials, laobur, equipment, fabrication, transportation, erection, installation and incidentais all complete as per direction of the Engineer-in-charge.Made of 3M or its equivalent 16 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67-2012 made of high intensity greade sheeting wide clause 801.3 friced over aluminium sheeting Type-IV 1.5mm thick supprorted on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian condition as per IRC 67-2012 & proof of the same in form of government report shall be uploaded while quoting tender. (Ch. 26 SI. No. 17)Stop Board 17 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67-2012 made of high intensity greade sheeting wide clause 801.3 friced over aluminium sheeting Type-IV 1.5mm thick supprorted on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian condition as per IRC 67-2012 & proof of the same in form of government report shall be uploaded while quoting tender. (Ch. 26 SI. No. 17)Speed Limit Board 18 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67-2012 made of high intensity greade sheeting wide clause 801.3 friced over aluminium sheeting Type-IV 1.5mm thick supprorted on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian condition as per IRC 67-2012 & proof of the same in form of government report shall be uploaded while quoting tender. (Ch. 26 SI. No. 17)30x90 cm (left/Right) Object Hazard 19 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC : 67-2012 made of high intensity greade sheeting wide clause 801.3 friced over aluminium sheeting Type-IV 1.5mm thick supprorted on a mild steel angle iron post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian condition as per IRC 67-2012 & proof of the same in form of government report shall be uploaded while quoting tender. (Ch. 26 SI. No. 17)90 cm equlateral tringle with diffnitation plate size (20cm x 60cm) . Last date of submission for this tender is 2025-01-28. This is a Safety Consultancy Service tender in etawah, Uttar Pradesh