Moradabad Development Authority

Moradabad Development Authority has published Tender For Work of lighting from Kashipur Tiraha to Jama Masjid Road and other lighting arrangements - S/E of S.T. pole S.P.-32 pole 9.00 Mtr. long with plinth including excavation & back filling etc. in 1:3:6 cement concrete with cap and base plate etc.all comp.(PWD SOR 2018 Item NO613) 2 Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 110 to 120 Watt. Confirming to IP 66Protection complete in all respect (halonix, philips jaguar) CAT- AAA 1424/2018 3 S/F of 63 amp 415 volt. Main switch comp. in all respect(PWD SOR S.I. No. 316 Cat - B Make Heavells. SOR/2018) 4 Painting of electric pole with two coats of aluminum paint over red oxide comp. in all respect (PWD SOR Item No 634/2018). 5 Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (PWD SOR Item NO 501/ 2018)- 50 Sq.mm. x3-1/2 core 501(l)/2018 6 25 Sq.mm. x3-1/2 core 501(j)/2018 7 S/F of palm or pin type copper tinplanted cable socket (lug) to the cable leads etc. comp. (504/2018)50 Sq.mm.504(g)/2018 8 25 Sq.mm. 504 (e)/2018 9 S/F of GI Pipe (1.5 inch) dia, 1.00 mtr long as Designed for fixing of street light ftitting on pole complete as per direction of E/I. (bracket pipe) 10 Supply & erection of D clamps of 38 mm x 6 mm flat iron for wall /roof type service bracket with bolts, nuts etc.complete in all respects including painting with aluminium paint.S.I. No. 624/2018 11 S/L of 1.1 KV 3 X 50 + 1 X35 + 1 X 16 Sq.mm aluminum alloy bare messenger aerial bunch as per I.S. : 14255 including supply of material, labour T&P etc. all complete as per U.P.P.C.L. approved(Rate Analysis as per approved by UPPCL 2023-2024) 12 S/F of holding clamp for poles including nuts bolts etc. complete as per U.P.P.C.L. approved (P.S.R.) 13 S/F of dead and clamp for poles including nuts bolts etc. complete as per U.P.P.C.L. approved (P.S.R.) 14 S/F of suspension clamp for poles including nuts bolts etc. complete as per U.P.P.C.L. approved (P.S.R.) 15 S/F of Piercing clamp for poles including nuts bolts etc. complete as per U.P.P.C.L. approved (P.S.R.) 16 S/F of P.G. clamp for poles including nuts bolts etc. complete as per U.P.P.C.L. approved (P.S.R.) 17 Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect. 807(PWD)SOR-2018(F)(ii) 40 A TPN 18 Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable enteies Electrical control panel with TPN MCCBs (Four pole 36 KA with thermal maganatic release) Switches complete and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA, P.F., KW etc.) in each phase with touch type selector switches for different reading, instrument fuses, current transfomer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCBs shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2mm. Cubicle type switch board shall be of cat A & B only.Incoming200 Amp. MCCB-1 NoOutgoing(a) 100 Amp. MCCB-2 Nos.(ii) Cat. B. Pannel Cubicle Type each 812/2018 . Last date of submission for this tender is 2025-06-27. This is a Electrification Work tender in Moradabad, Uttar Pradesh