Kisan Sahkari Chini Mills Limited

Kisan Sahkari Chini Mills Limited has published Tender For Supply Of C.I/C.S/G.M. Casting Items For Season 2025-26 - C.I. Items such as bush, rod, hollow, drum, square etc as per drg. Rough machine -Do-Supply Basis -Do-Conversion Basis G.M. Items such as bush, rod, hollow, drum,square etc as per drg. Rough machine -Do-Supply Basis -Do-Conversion Basis G.M. bearing of side roller, top roller, bottom roller, transmission gear etc. as per drg. Dully machined in 85:5:5:5 ratio -Do- Supply Basis -Do- Conversion Basis C.I. wheel for lime slakar as per drg. & ETP Clarifier as per drg -Do- Supply Basis -Do- Conversion Basis C.I. drum coupling as per drg. 8& below -Do- Supply Basis -Do- Conversion Basis C.I. drum coupling as per drg. 10& above -Do- Supply Basis -Do- Conversion Basis C.I. scraper as per drg. No.KSCMS/MH-15R1 rough machine -Do- Supply Basis -Do- Conversion Basis C.I. Nozzle as per drg. -Do- Supply Basis -Do- Conversion Basis C.I. boiler ash plate for gratebar as per drg. -Do- Supply Basis -Do- Conversion Basis C. lever for boiler as per sample: -Do- Supply Basis -Do- Conversion Basis Repairing/Replacement of hy.cap liner (after repairing/replacement of liner hy.Tested of the pressure 4500 LBS/02 & polishing of R/M 85:5:5:5 completion (G.M) -Do- Supply Basis -Do- Conversion Basis C.I. mouth piece for boiler as per drg. -Do- Supply Basis -Do- Conversion Basis C.I. V belt pully (machined) with pilot bore per 10 mm OD per groove. -Do- Supply Basis -Do- Conversion Basis C.I. boiler door (Machinned) as per drg/sample Do- Supply Basis -Do- Conversion Basis Axle for tie rod crank as per drg. -Do- Supply Basis -Do- Conversion Basis C.I. worm wheel 72 teeth -Do- Supply Basis -Do- Conversion Basis C.I worm wheel 65 teeth -Do- Supply Basis -Do- Conversion Basis C.I flate coupling (different size per 10mm OD with pilot bore -Do- Supply Basis -Do- Conversion Basis C.S. Pick Off Gear (Spur) - Nos. of Teeth - 42, Module - 1.75 -Do- - Nos. of Teeth - 72, Module - 1.75 -Do- - Nos. of Teeth - 84, Module - 1.75 New Supply Basis CS/EN-9 worm Wheel for 40:1- Ratio R.G. Box New Supply Basis GM worm Wheel for 40:1- Ratio R.G. Box Replacement of GM linner for Mill Hydraulic Cap C.S. Trash Beam as per Drg. KSCMS/MH-96-93-2002 On Supply Basis C.S. Trash Beam as per Drg. KSCMS/MH-96-93-2002 On Conversion Basis C.S. Crown Pinion On Supply Basis C.S. Crown Pinion On Conversion Basis C.S. Base Plate of Bearing Housing as per drg. On Conversion Basis C.S. Base Plate of Bearing Housing as per drg. On Supply Basis C.S. Coupling Set as per drg. Supply Basis C.S. Coupling Set as per drg. Conversion Basis C.S. Trash Plate as per drg. Conversion Basis C.S. Trash Plate as per drg. Supply Basis C.S. Tail Bar as per drg. KSCMS/MH-694-017 Supply Basis C.S. Tail Bar as per drg. KSCMS/MH-694-017 Conversion Basis C.S. Rail for Cane Unloader Wheel as per drg. Supply Basis C.S. Rail for Cane Unloader Wheel as per drg. Conversion Basis C.S. Tei Bar for Mill Trash Plate as per drg. KSCMS/MH-43 Conversion Basis C.S. Tei Bar for Mill Trash Plate as per drg. KSCMS/MH-43 Supply Basis C.I Drum for Cane Unloader as per drg. KSCMS/MH- 522-2001 Supply Basis C.I Drum for Cane Unloader as per drg. KSCMS/MH- 522-2001 Conversion Basis C.S Cane Unloader gear wheel- No. of Teeth 68, Module - 6, PCD- 408, Outer Dia- 420, RD- 394.1 and Pinion teeth - 18, Module- 6, PCD- 108, OD- 120,as per drg. KSCMS/MH- 404-98 Supply Basis C.S Cane Unloader gear wheel- No. of Teeth 68, Module - 6, PCD- 408, Outer Dia- 420, RD- 394.1 and Pinion teeth - 18, Module- 6, PCD- 108, OD- 120, as per drg. KSCMS/MH- 404-98 Conversion Basis Spur Gear no. of Teeth - 19, M- 8, PCD-152, OD- 168, RD- 133mm, FW- 130mm as per drg. No. KSCMS/MH- 647-01 Supply Basis C.I V-Belt Pulley no. of Grooves -3, OD- 225mm, Thick.- 75mm, BORe- 115mm Supply Basis C.I V-Belt Pulley no. of Grooves -3, OD- 225mm, Thick.- 75mm, BORe- 115mm Conversion Basis CI beam as per drg. For Boiler conversion Basis CI beam as per drg. For Boiler Supply basis Center Pin EN-24 with CS Casting Complete for Mill Head Stock Lever Pin EN-24 with CS Axle Complete of Mill Head Stock CI Hanger for Bagasse Chute Approx 5mtr. . Last date of submission for this tender is 2025-07-01. This is a Workshop Machinery And Equipments tender in Bareilly, Uttar Pradesh