Military Engineer Services

Military Engineer Services has published Addition / Alteration To Building P-21 At Af Stn Jodhpur. 1 Material & Labour For Squared Rubble Walling, Jodhpur Type, Regular Coursed, Well Bonded, Bedded And Solidly Hearted, Built In Cement Mortar 1:6 Complete All As Specified And Directed By The Engineer-In-Charge. 2 Taking Downcement Or Cement Lime Plaster Work Any Description From Brick Or Stone Wall Etc. Including Raking Out Of Joints, Hacking For Key, Scrubbing Down With Water Etc Complete All As Specified & Directed By The Engineer-In-Charge. 3 Material & Labour For Roughening Surfaces Of Old Concrete Floor By Picking, Sweeping Clean And Washing Down With Water To Remove Dust, Etc Complete All As Specified & Directed By The Engineer-In-Charge. 4 Material & Labour For Extra Over Stone Walling For Hammer Dressing To Face Stones With Maximum Depression On Face From A Straight Edge Not Exceeding 20Mm And Dressing Face Beds And Joints As Specified To Squared Rubble Walling, Jodhpur Type Complete All As Specified & Directed By The Engineer-In-Charge. 5 Material & Labour For Rendering 15 Mm Thick In Cement Mortar 1:4, On Stone Masonry Surface Or Surface Other Than Fair Faces Of Brick Work, Surface Finished Smooth And Even Without Using Extra Cement Complete All As Specified & Directed By The Engineer-In-Charge. 6 Material & Labour For Rendering 10 Mm Thick In Cement Mortar 1:4, On Stone Masonry Surface Or Surface Other Than Fair Faces Of Brick Work, Surface Finished Fair And Even Without Using Extra Cement Complete All As Specified & Directed By The Engineer-In-Charge. 7 Material & Labour For Rendering 10 Mm Thick In Cement Mortar 1:4, On Brick Work Or Concrete Surfaces, Surface Finished Fair And Even Without Using Extra Cement Complete All As Specified & Directed By The Engineer-In-Charge. 8 Material & Labour For Preparation Of New Plastered Or Unplastered Surfaces Of Walls And Applyingtwo Coats Of Exterior Weather Proof Water Based Emulsion Paint Over A Coat Of Exterior Primer, Including Cleaning Of Windows, Doors, Internal Fittings & Any Other Surfaces By Removing Splashes / Spots After Finishing The Job And Leaving Premises, Clean And Tidy Complete All As Specified And As Directed By Engineer-In-Charge. 9 Material & Labour For Preparation Of New Plastered Or Unplastered Surfaces Of Walls And Applyingtwo Coats Of Oil Bound Distemper, White Or Tinted, Including Cleaning Of Windows, Doors, Internal Fittings & Any Other Surfaces By Removing Splashes / Spots After Finishing The Job And Leaving Premises, Clean And Tidy Complete All As Specified And As Directed By Engineer-In-Charge. 10 Supply & Fixing Approved Colour Aluminium Anodized Powder Coated ( Thickness Of Powder Coating Not Less Than 50 Micron ) Aluminium Frame / Shutters For Doors , Windows, Ventilators, Partition Wallwith One Or More Rebates Or Aluminium Section Of Two Or More Tracks In Case Of Sliding Windows, Including Joining Cleat For Fixing Etccomplete All As Specified & Directed By The Engineer-In-Charge. 11 Supply & Fixing Sheet Glass 5.5 Mm Thick, Ordinary Quality And Glazing, In Square Exceeding 0.5 Sqm In Each Pane Including Necessary Glazing Clips And Rubber Beading Etc Complete All As Specified & Directed By The Engineer-In-Charge. 12 Supply & Fixing Aluminium ( Extruded Section Body ) Door Closer Hydraulically Regulated, Designation No. 1 Universal Type, Suitable For Door Shutters Up To 700 Mm In Width And Of Weight Not More Than 35 Kg And Fixed Complete All As Specified & Directed By The Engineer-In-Charge. 13 Supply And Fixing 25 Mm Dia Stainless Steel Curtain Rod Decorative Type, Design And Pattern As Approved, Including Both End Supports Complete All As Specified And As Directed By Engr-In-Charge . 14 Supply And Fixing 25 Mm Dia Stainless Steel Curtain Finials For Curtain Rod Both Ends Complete All As Specified And As Directed By Engr-In-Charge. 15 Material & Labour For Dholpur Stone With Hammer Dressed Facework ( With Maximum Depression From A Straight Edge Held Against The Dressed Surface Not Exceeding 20Mm ) , About 40Mm High, 75Mm Deep In Straight Courses, Laid And Jointed In Cement And Stone Dust Mortar 1:3, Recess Pointed ( 10Mm X 20Mm ) With An Admixture Of White Cement And Dholpur Stone Dust 1:1 Complete All As Specified & Directed By The Engineer-In-Charge. 16 Material & Labour For 25 To 30 Mm Thick Dholpur Stone Cladding Gang Saw Cut With Machine Cut Edges, Uniform Colour Of Each Stone Size Not Exceeding 0.5 Sqm Area Fixed With And Including One Number Ss Clamps ( Grade - 202 ) Of Flat 30Mm X2mm, 150Mm Long Made To Shape In Each Slab, Making V Groove At Top And Bottom Of Stone And Drilling Hole For Hold Fastener, Polishing, Rubbing & Including Silicon Treatment Complete All As Specified & Directed By The Engineer-In-Charge. 17 Material & Labour For 25 To 30 Mm Thick Dholpur Stone Cladding With Engraved Design As Per Sample ( As Per Old Design Existing At Asite Or Approved By Ge ) , Uniform Colour Of Each Stone Size Not Exceeding 0.5 Sqm Area Fixed With And Including One Number Ss Clamps ( Grade - 202 ) Of Flat 30Mm X2mm, 150Mm Long Made To Shape In Each Slab, Making V Groove At Top And Bottom Of Stone And Drilling Hole For Hold Fastener, Polishing, Rubbing & Including Silicon Treatment Complete All As Specified & Directed By The Engineer-In-Charge.. Last date of submission for this tender is 2023-05-06. This is a Cutting Crimping And Punching Tools tender in Jodhpur, Rajasthan