Department Of Local Bodies

Department Of Local Bodies has published Kota Nagar Nigam South Bandha Goshala Tubewell And Nal Supply Electric Work 3 work name 2 Construction of tube well from ground level and upto 100 Metre depth and above sizes in all types of soils in alluvium strata by bailing method and without gravel packing as per IS : 2800 (Part-I & II) 1979 specifications (The work includes formation of cavity well at bottom by development with appropriate air compressor or bailer pumping and alsolowering of casing pipe but excluding cost of the casing pipe. The tube well should have a throughout bore as per nominal bore of casing pipe. The work would be completed after obtaining sand free water.). 150 mm dia nominal bore. 3 Construction of tube well 100 meter depth above in all type of rocks by DTH system and over burden, to accommdate casing pipe of following size in all types of soils and over burden including lowering of casing pipes,but excluding cost of casting pipes as per IS : 2800 (part-I & II) 1979specifications. the work would be completed after obtaining sand free water. the tube-well should have a throught bore as per nominal dia of casting pipe. 150 mm dia nominal bore 4 Supply of ERW M.S. black casing pipe ISI marked (IS : 4270/1992) of grade Fe 410 of following sizes at site of work. 150 mm dia nominal bore 5 Supply & fixing tube well cover of M.S. sheet ( 6 mm thick) with nuts and bolts complete for casing size. 150 mm dia nominal size 6 Wiring for sub mains ISI marked (IS : 694) 1100 volts grade PVC insulated flat twin core sheathed solid aluminium conductor with 10 SWG G.I. support wire duly clipped etc. as required. 7 P/Laying ISI marked P.V.C. insulated submersible cable confirming to IS ; 694 with flexible copper condactor including making connection etc. required. 4.0 sq.mm 3 core flat/round 8 Providing of synthetic rope for submersible pump ISI marked (IS : 5175) of following sizes. 12 mm (suitable up to 50 mm OD pipe) 9 Providing & fixing of HDPE pipe ISI mark (IS :4984/95) for water supply (suitable for submersible & jet pump) with required fittings. for vertical installtion, 40 mm OD 6kg/cm2 10 SITC of radial/mixed flow submersible motor pump sets ISI marked (IS :8034 – 1989) of approved make with required accessories including making connection suitable for T.W./D.C.B./ open well the job includes lowering of riser pipe, G.I./H.D.P.E. pipe with rope, cables, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pupms set and supply of water to water mains, complete in all respect.100 mm diameter submersible pump shall have following HP rating, phase, head, minimum discharge respectively.5.0 HP, 1-Ø, (120-220)Mtr 11 Supply and fixing of oil / Air break starter panel made out of sheetsteel powder coated enclosure comprising of over load protection relay, short circuit & single phasing protection, ON / OFF push buttons ammeter, voltmeter, indicating lamps etc. complete in all respect suitable for following rating motors. 0.5 HP to 5.0 HP 12 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 25 mm nominal outer dia .Pipes. 13 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes. 14 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 32 mm nominal outer dia .Pipes. 15 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 20 mm nominal bore. 16 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 25 mm nominal bore. 17 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : 32 mm nominal bore. 18 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore 19 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore 20 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore 21 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore 22 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore. Horizontal 23 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore. Vertical 24 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 32 mm nominal bore. Horizontal 25 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 32 mm nominal bore. Vertical . Last date of submission for this tender is 2022-04-20. This is a Other Adhesives And Sealants tender in Kota, Rajasthan