National Aluminium Company Limited

National Aluminium Company Limited has published Bids Are Invited For Various Fabricated Spares For Rodding Shop - Punch Assembly For Thimble Removal Press As Per Drawing No:Rs-I / Sp / M / A2 / 1625, Rev.01 Material: En 24, Ear Pin With Split Pin For Bell Grab In Rs-1 As Per Drg No: Rod / Ga / Mech / A1 / 4333 Rev-1 There Are 3 Power En24 Note: The Orientation Of The Trimmed Pin Head Shall Be Made Correctly With Reference To The Split Pin Position As Shown In Drawing. Load Bar Acutator In Rodding Shop-Las Per Drawing: Rod / Sp / Mech / A3 / 4182, Rev-1. Shaft, Item-1 Drg No Nal / Pnds / Rod Mecha A1 / 210 With Standard Key Ways For Roller Conveyor Of H / Uh M / C In Rs-1 Note: Item Should Be Provided With Antirust Coating And Wrapped With Polyeurethene Shaft With Standard Keys As Per Drawing No. Nal / Pnd / S / Rod / Mecha1 / 210, Item No.2 Note: Tem Should Be Provided With Antirust Dating And Wrapped With Polyeurethene Pre-Breaking Tool Hyd Cylinder Rear End Pin D:1400 X 1355 As Per Item No 22 Of Dwg No. Rsimech / Spr / A2 / 11186, Sht3 / 3 Rev-1 Rod Handling Arm Fom Erimble Press In Rodding Shop-I In Assembled Condition Comprising Of Item No. 1 To 14. As Per Drg Rod / Sp / Mech / A1 / 4247, Rev-2 Base Plate For Charging Hoist Lt Wheel Assembly As Per Item 1 Dwg.No.Rs-1 / Mech / Spr / A1 / 11412- Evel Drive Wheel For Charging Hoist Lt Wheel Assembly As Per Item 2, Dwg.No.Rs-1 / Mech / Spr / A1 / 11412- Rev-1 Cover Flange For Charging Hoist Lt Wheel Assembly As Per Item 3, Dwg.No.Rs-1 / Mech / Spr / A1 / 11412- This-1 Lt Shaft For Charging Hoist Lt Wheel, Assembly As Per Item 4, Dwg.No.Rs-1 / Mech / Spr / A1 / 11412 Rev-1 Gear Pinion For Charging Hoist Lt Wheel Assembly As Per Item 5, Dwg No.Rs-1 / Mech / Spr / A1 / 11412- Rev-1 Bearing Hub For Charging Hoist Lt Wheel Assembly As Per Item 6, Dwg.No.Rs-1 / Mech / Spr / A1 / 11412- Rev-1 Axle For Drive Wheel For Charging Hoist Li Wheel Assembly As Per Item 7, Dwg.No.Rs-1 / Mech / Spr / A1 / 11412- This-1 Cover Tray For Pawl Bar Of Rodding Bench Castingmachine In Rs-1 As Per Drawing No. Rs-I / Mech / Spr / A2 / 11065 Rev-1 Tem No.1 To 4 De Shaft For Track Guide Roller For Aux Pusher Of Bath Breaking Machine In Rs-2 As Per Dwg.No.Rs2 / Mech / Spr / A3 / 9764 Nde Shaft For Track Guide Roller For Aux Pusher Of Bath Breaking Machine In Rs-2 As Per Dwg No.Rs2 / Mech / Spr / A3 / 9763 Beam Guide Roller Pin D.25Xl 113 As Per Tem No-1, Dwg-Rs-Ii / Mech / Spr / A2 / 11602, Sh-1 / 5 Beam Guide Roller Pin D.25Xl 102 As Per Item No-2, Dwg-Rs-Ii / Mech / Spr / A2 / 11602, Sh-1 / 5 Spacer Beam Guide Roller D 26X1.10 As Per Tem No-3, Dwg-Rs-Ii / Mech / Spr / A2 / 11602 Sh-1 / 5, Guide Wheel Axle D49x1200 Along With Locking Plate D.60Xl10 For Old Matting Table As Per Tem No.4, Dwg-Rs-Ii / Mech / Spr / A2 / 11602, Sh-1 / 5 And Tem No-10, Dwg-Rs-Ii / Mech / Spr / A2 / 11602. Sh-2 / 5 Encoder Shaft 157 For Laddle Tilting Of Casting Machine As Per Tem No-5, Dwg-Rs-Ii / Mech / Spr / A2 / 11602, Sh-1 / 5 Guide Wheel D.101 Beam Guide Roller As Per Tem No-6, Dwg-Rs-Ii / Mech / Spr / A2 / 11602 Sh-1 / 5 Drive Shaft D.75 1.3212.5 Ct Wheel Of New Casting M / C As Per Tem No 18, Dwg Rs-U / Mech / Spr / A2 / 11602, Sh-4 / 5, Drive Shaft D.70 11698 Lt Wheel, New Matting Mac As Per Tem No-20, Dwg-Rs-Ii / Mech / Spr / A2 / 11602, Sh 5 / 5 Guide Wheel Assy For Bucket Of Skip Hoist F-145 And F-60 Of Rodding Shop-Ii, As Per Drg No.Rs-Ii / Mech / Ga / A2 / 11329, Sh-1 / 2 And 2 / 2 Note Bearings Used Shall Be Of Skf Fag / Nin Make Only. The Size Of Bearing Is 6206 22. The Assembly Shall Be Painted With 2 Coats Of Glossy Enamel Paint ( Grey ) Tail Take Up Pulley For Belt Width 650Mm For Bc 70 In Crs As Per Drawing No Butt2 / Mech / Spr / A2 / 9937, Sr No.2, Face Width 750Mm, Brg Centre Distance 1100Mm, Od Of Pulley 350 Mm, Shaft Dia At Bearing 55Mm, Shell Thickness: 10 Mm. Note 1. Detail Note In Drawing Has To Be Taken Care Of While Manufacturing Of The Pulleys 2. Pulley Has To Be Manufactured As Per Standard Is 8531. 3. Continuous Welding Shall Be Done Stress Relieving Shall Be Done After Welding But Before Machining. 5. Static Balancing Shall Be Done For Pulley Shaft Assembly, 6. Shaft Has To Be Coated With Good Quality Rust Prevention Lubricant And Wrapped Properly With Polythene, Block For Apron Roller In Crs As Per Drawing No.Crs / Sp / Mech / A2 / 7307, Item Sl No. 9, Tie Rod With Washer And Nuts Assembly For Secondary Crusher 10X36 Of Butt System As Per Drawing No.Butt-I / Mech / Spr / A3 / 10866, Pin Bush Assy For Draw Back Rod Of Dragon Crusher In Butt-1 As Per Drg.No.Butt-1 / Mech / Spr / A3 / 9826, Item No.1 To 4 Total Quantity : 245. Last date of submission for this tender is 2024-05-15. This is a Crushers Breakers and Grinders tender in Angul, Odisha