Public Works Department

Public Works Department has published General-Sr 2022-23 -Providing Sunshade With Truss Work For Ngo Quarters Attached To Govt Medical College , Kozhikode.-Work-General Civil Work -Steel Work In Built Up G I Tubular ( Round, Square Or Rectangular Hollow Tubes Etc. ) Trusses Etc., Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer, Including Welding And Bolted With Special Shaped Washers Etc. Complete 3 50.10.2:Steel Work For Purlin / Single Section With G I Pipes Including Cutting, Hoisting, Fixing In Position And Applying A Priming Coat Of Approved Steel Primer, Including Welding And Bolted With Special Shaped Washers Etc. Complete 4 12.50:Providing And Fixing Precoated Galvanised Iron Profile Sheets ( Size, Shape And Pitch Of Corrugation As Approved By Engineer-In-Charge ) 0.50 Mm ( +0.05% ) , Total Coated Thickness With Zinc Coating 120 Grams Per Sqm As Per Is: 277, In 240 Mpa Steel Grade, 5-7 Microns Epoxy Primer On Both Side Of The Sheet And Polyester Top Coat 15-18 Microns. Sheet Should Have Protective Guard Film Of 25 Microns Minimum To Avoid Scratches During Transportation And Should Be Supplied In Single Length Upto 12 Metre Or As Desired By Engineer-In-Charge. The Sheet Shall Be Fixed Using Self Drilling / Self Tapping Screws Of Size ( 5.5X55mm ) With Epdm Seal, Complete Upto Any Pitch In Horizontal / Vertical Or Curved Surfaces, Excluding The Cost Of Purlins, Rafters And Trusses And Including Cutting To Size And Shape Wherever Required. 5 13.61.1:Painting With Synthetic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade:Two Or More Coats On New Work 6 21.7.2:Providing And Fixing Machine Moulded Aluminium Covering Of Approved Pattern & Design, Made Out Of Machine Cut Aluminium Sheet And Machine Holed For Receiving Dash Fastener, Over Expansion Joints On Vertical Surfaces / Ceiling Floors, The Fixing On Plate In One Row On One Side Of Joint Only Shall Be Done With Stainless Steel Dash Fastners Of 8 Mm Dia And 75 Mm Long Bolt Including Providing Aluminium - Washers 2 Mm Thick 15 Mm Dia, At A Staggered Pitch Of 200 Mm Centre To Centre Including Drilling Holes In The Receiving Surface And Providing Expandable Plastic Sleeves In Holes Etc.Complete As Per Drawing And Direction Of Engineer -In-Charge.Powder Coated Aluminium Sheet 2.5 Mm Thick ( Minimum Thickness Of Powder Coating 50 Micron ) 7 21.8.1:Filling The Gap In Between Aluminium Frame & Adjacent Rcc / Brick / Stone Work By Providing Weather Silicon Sealant Over Backer Rod Of Approved Quality As Per Architectural Drawing And Direction Of Engineer-In -Charge Complete.Upto 5 Mm Depth And 5 Mm Width 8 14.72:Providing And Fixing Double Scaffolding System ( Cup Lock Type ) On The Exterior Side, Upto Seven Story Hight Made With 40 Mm Dia. M.S. Tube 1.5 M Centre To Centre, Horizontal & Vertical Tubes Joining With Cup & Lock System With M.S. Tubes, M.S. Tube Challies, M.S. Clamps And M.S. Staricase System In The Scaffolding For Working Platform Etc. And Maintaining It In A Serviceable Condition For The Required Duration As Approved And Removing It There After. The Scaffolding System Shall Be Stiffened With Bracings, Runners, Connection With The Building Etc Wherever Required For Inspection Of Work At Required Location With Essential Safety Features For The Workmen Etc. Complete As Per Directions And Approval Of Engineer- In Charge. The Elevational Area Of The Scaffolding Shall Be Measured For Payment Purpose. The Payment Will Be Made Once Irrespective Of Duration Of Scaffolding. Note:- This Item To Be Used For Maintenance Work Judicially, Necessary Deduction For Scaffolding In The Existing Item To Be Done .. Last date of submission for this tender is 2023-01-25. This is a Coats And Jackets tender in Kozhikode, Kerala