Kerala State Electricity Board

Kerala State Electricity Board has published Tender For Mf Ii Kolathara Fabrication Of Line Materials Second Phase; 1 Fabricating 2 line cross arms using MS Channel 75x40mm 61cm long with2 nos. 18 mm dia holes in each flange by using drilling machine to hold the pin insulator vertically and 2 nos 16mm dia holes in web side as per drawing including cutting, leveling, punching and stacking the finished products at suitable placesincluding scrap in such a manner that the items can be easily counted in numbers etc. completeas per direction of Departmental Officers. The rate will include the labour charges, shearing tools, die set, punch ect.(MS Channel 75X40 mm will be issued departmentaly free of cost at site) 2 Fabricating 4 line cross arms using MS Channel 75x40mm, 1.065 m long with4 nos. 18 mm dia holes on both sides of flange by using drilling machine to hold the pin insulator vertically and 2 nos 16mm dia holes in web side as per drawing including cutting, leveling, punching and stacking the finished products at suitable placesincluding scrap in such a manner that the items can be easily counted in numbers etc. completeas per direction of Departmental Officers. The rate will include the labour charges, shearing tools, die set, punch ect.(MS Channel 75X40 mm will be issued departmentaly free of cost at site) 3 Fabricating 11KV V- cross arms usingMS Channel 75x40mm ( departmental free issue) cutting by gas,drilling 4Nos. of 23mm dia holes and 2Nos 20mm dia holes, bending into required shape and jointed by arc weldingin both sides of each gas cutting portion including cutting of 4Nos 50mm longMSF 50x6mm / 50X8mm pieces punched with 23mm dia holes which isplaced on the top of 4Nos drilled holes and weldedas per drawing including flux removal ,counting and stackingthe finished goods, conveying and stacking cut bits & scrap etc. to the place pointed out by thedepartmental officers etc. complete. (Charges inclusive of labour, welding electrodes,cutting gas, punch & die, drill bits etc.) 4 Fabricating 33KV V- cross arms using MS Channel 100x50mm (departmental free issue), cutting by gas,drilling 4Nos. of 26mm dia holes and 2Nos 20mm dia holesbending into required shape and jointed by welding drilling necessary holesas per Boards specificationand drawing including flux removal ,counting and stackingthe finished goods, conveying and stacking as per the direction of departmental officers etc. complete. 5 Fabricating 1.8m channel cross arm usingMS channel 75x40 mm (departmental free issue) with 22mm dia drilled/punched holes 4 Nos as per Boards specification and drawing including gas cutting, levelling stacking fabricated items & conveying the scrap at suitable place as per the direction of the departmental officersetc. complete (Charges inclusive oflabour & consumables such as cutting gas, LPG, punch, die etc.) 6 Fabricating 2.4m channel cross arm usingMS channel 75x40 mm (departmental free issue) with 22mm dia drilled/ punched holes 5 Nos as per Boards specification and drawing including gas cutting, levellingand stacking fabricated items and conveying scrap at suitable place as per the direction of the departmental officers etc. complete (Charges inclusive oflabour & consumables such as cutting gas, LPG, punch & die etc.) 7 Fabricating 3.0mchannel cross arm using MS channel 100x50mm(departmental free issue), cutting to 3m length and 22mm dia.drillied/punched holes 7 Nos as per Boardsspecification and drawing including gas cutting, levellingand stacking the finished products & scrap at suitable place as per the direction of the departmental officersetc. complete. (Charges inclusive of cost of labour & consumables, such as cutting gas, LPG,drill bit, punch & die etc.) 8 Fabricating 3.15mchannel cross arm using MS channel 100x50mm(departmental free issue), cutting to 3m length and 22mm dia.drillied/punched holes 7 Nos as per Boardsspecification and drawing including gas cutting, levellingand stacking the finished products & scrap at suitable place as per the direction of the departmental officersetc. complete. (Charges inclusive of cost of labour & consumables, such as cutting gas, LPG,drill bit, punch & die etc.) 9 Fabricating back clamps for LT(2/4 Line) cross arms in new design using MSF 50x6mm (departmental free issue),cutting 40 cm long bending into required shape, punching 2Nos 16 mm dia holes as per design and drawingincluding stacking the finished productsin such a manner that the item can be easily counted in numbers, collecting and conveying the cut bits and scrap as per the direction of the departmental officers etc. complete.(Charges inclusive of labour and cost of cutting blade,etc.) 10 Fabricating stay rod of length 1.70m for LT linesusing16 mm rod as per design and drawing including marking,shearing, levlling,threading one end to a length of 5 cm suitable to nut available in the market making round hook in the other end and welding the joint andstacking the finished products at suitable places in such manner that the item can be easily countable in numbers as per the direction of the departmental officers.(Charges inclusive of labour, shearing tool, welding electrodes and consumables etc. complete.) 11 Fabricating 20mm Stay Rod of length 1.70m for HT lines using 20mm diaM.S.Rods as per design including marking, shearing, levelling, threading one end to length of 5cm suitable to nut of dia 3/4, and making a round hook in the other end and welding the joint and stacking the finished products at suitable places in such a manner that the items can be easily counted in numbers and punching stamp marks on the product as per the direction of departmental officers etc. complete. (Charges inclusive of cost of labour & consumables, such as cutting gas, LPG, punch & die, drill bit etc.)complete. 12 FabricatingAnchor plate of size 200x200 mm 8 mm thick platefor 16 mm stay rod (HT Stay rod) by using 600 MS plate of any size by cuttingin prescribed size of 200x200 mm providing 20mm hole in centre of plate by drilling including removalof rust and chipping of flux and stacking in appropriate places as per the direction of Departmental officers in site such a manner that the product can be easily counted. . Last date of submission for this tender is 2025-10-21. This is a Fabrication Work tender in Kozhikode, Kerala