Hll Lifecare Limited

Hll Lifecare Limited has published Civil And Electrical Works For Renovation And Upgradation Of Primary Health Centre To Family Health Centre At Odakkayam , Malappuram , Civil Work , Earth Work , Earth Work In Excavation By Mechanical Means ( Hydraulic Excavator ) / Manual Means In Foundation Trenches Or Drains ( Not Exceeding 1 . 5 M In Width Or 10 Sqm On Plan ) , Including Dressing Of Sides And Ramming Of Bottoms , Lift Up To 1 . 5 M , Including Getting Out The Excavated Soil And Disposal Of Surplus Excavated Soil As Directed , Within A Lead Of 50 M . All Kinds Of Soil , Filling Available Excavated Earth ( Excluding Rock ) In Trenches , Plinth , Sides Of Foundation Etc . In Layers Not Exceeding 20 Cm In Depth , Consolidating Each Deposited Layer By Ramming And Watering , Lead Up To 50 M And Lift Up To 1 . 5 M . , Cement Concrete , Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level:1:4:8 ( 1 Cement : 4 Coarse Sand : 8 Graded Stone Aggregate 40 Nominal Size ) , R . C . C . Work , Reinforced Cement Concrete Work In Beams , Suspended Floors , Roofs , Having Slope Up To 150 Landings , Balconies , Shelves , Chajjas , Lintels , Bands , Plain Window Sills , Staircases And Spiral Stair Cases Up To Floor Five Level Excluding The Cost Of Centering , Shuttering , Finishing And Reinforcement , With1:1 . 5:3 ( 1 Cement : 1 . 5 Coarse Sand ( Zone Iii ) : 3 Graded Stone Aggregate 20 Mm Nominal Size ) . , Centering And Shuttering Including Strutting , Etc . And Removal Of Form For:Foundations , Footings , Bases Of Columns , Etc For Mass Concrete , Steel Reinforcement For R . C . C Work Including Straightening , Cutting , Bending , Placing In Position And Binding All Complete Upto Plinth Levelthermo - Mechanically Treated Bars Of Grade Fe-500D Or More , Masonry Works , Half Brick Masonry With Common Burnt Clay F . P . S . ( Non Modular ) Bricks Of Class Designation 7 . 5 In Superstructure Above Plinth Level Up To Floor V Level . Cement Mortar 1:3 ( 1 Cement : 3 Coarse Sand ) , Brick Work With Common Burnt Clay F . P . S . ( Non Modular ) Bricks Of Class Designation 7 . 5 In Superstructure Above Plinth Level Up To Floor V Level In All Shapes And Sizes In:Cement Mortar 1:4 ( 1 Cement : 4 Coarse Sand ) , Random Rubble Masonry With Hard Stone In Foundation And Plinth Including Levelling Up With Cement Concrete 1:6:12 ( 1 Cement : 6 Coarse Sand : 12 Graded Stone Aggregate 20 Mm Nominal Size ) Up To Plinth Level With:Cement Mortar 1:6 ( 1 Cement : 6 Coarse Sand ) , Plastering , 12 Mm Cement Plaster Finished With A Floating Coat Of Neat Cement Of Mix:1:3 ( 1 Cement : 3 Fine Sand ) , Aluminium Works , Providing And Fixing Aluminium Work For Doors , Windows , Ventilators And Partitions With Extruded Built Up Standard Tubular Sections / Appropriate Z Sections And Other Sections Of Approved Make Conforming To Is : 733 And Is: 1285 , Fixing With Dash Fasteners Of Required Dia And Size , Including Necessary Filling Up The Gaps At Junctions , I . E . At Top , Bottom And Sides With Required Epdm Rubber / Neoprene Gasket Etc . Aluminium Sections Shall Be Smooth , Rust Free , Straight , Mitred And Jointed Mechanically Wherever Required Including Cleat Angle , Aluminnium Snap Beading For Glazing / Paneling , C . P . Brass / Stainless Steel Screws , All Complete As Per Architectural Drawings And The Directions Of Engineer-In-Charge . ( Glazing , Paneling And Dash Fasteners To Be Paid For Separately ) :For Fixed Portionpowder Coated Aluminium ( Minimum Thickness Of Powder Coating 50 Micron ) , For Shutters Of Doors , Windows & Ventilators Including Providing And Fixing Hinges / Pivots And Making Provision For Fixing Of Fittings Wherever Required Including The Cost Of Epdm Rubber / Neoprene Gasket Required ( Fittings Shall Be Paid For Separately ) Powder Coated Aluminium ( Minimum Thickness Of Powder Coating 50 Micron ) , Providing And Fixing 12 Mm Thick Prelaminated Particle Board Flat Pressed Three Layer Or Graded Wood Particle Board Conforming To Is : 12823 Grade I Type Ii , In Panelling Fixed In Aluminum Doors , Windows Shutters And Partition Frames With C . P . Brass / Stainless Steel Screws Etc . Complete As Per Architectural Drawings And Directions Of Engineer - In- Charge . Pre- Laminated Particle Board With Decorative Lamination On Both Sides , Providing And Fixing Glazing In Aluminium Door , Window , Ventilator Shutters And Partitions Etc . With Epdm Rubber / Neoprene Gasket Etc . Complete As Per The Architectural Drawings And The Directions Of Engineer - In -Charge . ( Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item ) :With Float Glass Panes Of 5 . 50 Mm Thickness , Providing And Fixing 100 Mm Brass Locks ( Best Make Of Approved Quality ) For Aluminium Doors Including Necessary Cutting And Making Good Etc . Complete , Providing And Fixing Anodised Aluminium Grill ( Anodised Transparent Or Dyed To Required Shade According To Is : 1868 With Minimum Anodic Coating Of Grade Ac 15 ) Of Approved Design / Pattern , With Approved Standard Section And Fixed To The Existing Window Frame With C . P Brass / Stainless Steel Screws @ 200 Mm Centre To Centre , Including Cutting The Grill To Proper Opening Size For Fixing And Operation Of Handles And Fixing Approved Anodised Aluminium Standard Section Around The Opening , All Complete As Per Requirement And Direction Of Engineer-In-Charge . ( Only Weight Of Grill To Be Measured For Payment ) . , Providing And Fixing Ptmt Tower Bolts With 12 Mm One Piece Rod Inside And Necessary Screws Etc . , Complete . 202X42x18 Mm Weighing Not Less Than 78 Gms , Providing And Fixing Aluminium Tubular Handle Bar 32 Mm Outer Dia , 3 . 0Mm Thick & 2100 Mm Long With S . S . Screws Etc . Complete As Per Direction Of Engineer -In-Charge . Polyester Powder Coated Minimum Thickness 50 Micron Aluminium Tubular Handle Bar , Providing And Fixing Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer ( Having Brand Logo With Isi , Is : 3564 , Embossed On The Body , Door Weight Upto 36 Kg To 80 Kg And Door Width Form 701 Mm To 1000 Mm ) , With Double Speed Adjustment With Necessary Accessories And Screws Etc . Complete . , Providing And Fixing 150 Mm Bright Finished Floor Brass Door Stopper With Rubber Cushion , Necessary Brass Screws Etc . To Suit Shutter Thickness Complete , Steel Works , Structural Steel Work Riveted , Bolted Or Welded In Built Up Sections , Trusses And Framed Work , Including Cutting , Hoisting , Fixing In Position And Applying A Priming Coat Of Approved Steel Primer All Complete . , Providing And Fixing Stainless Steel ( Grade 304 ) Railing Made Of Hollow Tubes , Channels , Plates Etc . , Including Welding , Grinding , Buffing , Polishing And Making Curvature ( Wherever Required ) And Fitting The Same With Necessary Stainless Steel Nuts And Bolts Complete , I / C Fixing The Railing With Necessary Accessories & Stainless Steel Dash Fasteners , Stainless Steel Bolts Etc . , Of Required Size On The Top Of The Floor Or The Side Of Waist Slab With Suitable Arrangement As Per Approval Of Engineer-In-Charge , ( For Payment Purpose Only Weight Of Stainless Steel Members Shall Be Considered Excluding Fixing Accessories Such As Nuts , Bolts , Fasteners Etc . ) , Providing Corrugate G . S . Sheet Roofing Including Vertical / Curved Surface Fixed With Polymer Coated J Or L Hooks , Bolts And Nuts 8 Mm Diameter With Bitumen And G . I . Limpet Washers Or With G . I . Limpet Washers Filled With White Lead , Including A Coat Of Approved Steel Primer And Two Coats Of Approved Paint On Overlapping Of Sheets Complete ( Up To Any Pitch In Horizontal / Vertical Or Curved Surfaces ) , Excluding The Cost Of Purlins , Rafters And Trusses And Including Cutting To Size And Shape Wherever Required . 1 . 00 Mm Thick With Zinc C. Last date of submission for this tender is 2019-10-26. This is a Earth Moving Machinery tender in Phc Odakkayam, Kerala