Forest Department

Forest Department has published Tender For Estimate for the cost of upgradation and improvement of camping facility at Viripara in Mankulam Range during 2025-2026--- 1 Improvement Work 2 13.48.1Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm 3 13.111.1Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface 4 15.41Dismantling cement asbestos or other hard board ceiling or partition walls includingstacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. 5 50.12.4.2Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel boardceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) 6 21.5Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessaryC.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall withstainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). 7 21.6Providing and fixing 6 mm dia. G I level adjusting hangers ( upto 1200 mm length),fixed to roof slabs by means of ceiling cleats made out of G.I flat 40x3 mm size 60mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer -in-Charge. 8 9.118.2Providing and fixing to existing door frames30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of H section, a uPVC hollow section ofsize 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mmgalvanised M.S. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of Engineer-in- harge 9 50.9.1.1Providing wood work in frames of doors, windows, clerestory windows and otherframes, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood 10 9.92.1Providing and fixing chromium plated brass handles with necessary screws etc. complete:125 mm 11 10.16.1Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 12 OD111805/2025-2026Providing and fixing precoated galvanised iron profile sheets (size, shape and pitchofcorrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steelgrade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15 18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses and including cutting tosize and shape wherever required. 13 17.20.1Providing and fixing solid plastic Seat with lid for pedestal type W.C. pan complete:White solid plastic seat with lid 14 17.18.2Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete.10 litre capacity - coloured 15 OD161536/2025-2026Lumpsum amount for the Listed works 1)Existing truss work painting 2)Siliconfilling if required. 3)Skilled Masson for Shifting door shutter and check all doors and shutters. 4) Providing and fixing iron shelfs. 5)Acid wash allover the first floor area. 6)Electrical and plumping works (false ceiling lights, tube lights, plug points) if necessary. 7)providing and fixing curtain for windows and toilet area with allaccessories if required. 16 Provision for GST (18%) . Last date of submission for this tender is 2025-09-25. This is a Tour And Travel Agency tender in Idukki, Kerala