Department of Higher Education

Department of Higher Education has published Bids Are Invited For Pyrolytic Oven And Emulsion Sampling Equipment - PARTICLE CHARGE TESTER (ASTM D244) WITH ACCESSORIES Compliance Standards: EN 1430, ASTM D244 APPARATUS FOR DISTILLATION OF EMULSIFIED ASPHALT (WITH RING BURNER) (ASTM D244, ASTM D6997) - WITH ACCESSORIES Complies with following International Standards: ASTM 244, ASTM D6997, AASTHO T59, IS 8887 FINE SIEVE - 10 CM DIA-BRASS-0.600MM (600 MIC) A circular sieve approximately 100 mm diameter and 40 mm height. As per IS:8887-2018. SAYBOLT VISCOMETER WITH DIGITAL CONTROLLER AND MOTORISED STIRRER - ASTM D88 Complies with International Standards: IS:3117-2019/ASTM D88 Electrically heated model complete with One saybolt tube and electrical control panel. Including 1. FLASK-GLASS 60 ML FOR SAYBOLT VISCOMETER 2. STOPWATCH - DIGITAL APPARATUS FOR DETERMINATION COAGULATION OF EMULSION -IS-8887, ANNEX-C Apparatus for determination of Coagulation of Emulsion at low temperature as per IS-8887 Annex- C, consisting of 2 nos. glass boiling tube (150 X 25mm) with cork with central hole 2 nos. sieve 600 microns, 4 nos. 600ml. beakers and water bath thermostatically controller for 2 holes. APPARATUS FOR DETERMINATION OF STORAGE STABILITY - IS 8887, ASTM D6930 PARTICLE CHARGE TESTER BIS 8887 WITH ACCESSORIES APPARATUS FOR COATING ABILITY AND WATER RESISTANCE - IS 8887:2018 (ANNEX F) APPARATUS FOR STABILITY TO MIXING WITH CEMENT -IS 8887, ANNEX-G APPARATUS FOR DETERMINATION OF RESIDUE ON EVAPORATION - IS 8887 WATER CONTENT OF BITUMEN EMULSION - WITH HEATER As per IP-291 ,with stand and clamp., PYROLYTIC CLEANING OVEN Model No. : EIE-PACO-01 HSN : 90248099 The Pyrolytic Oven is used for performing safe, solvent-free cleaning of asphalt and other organic residues from glass and labware. Even trace residues of organic contaminants from asphalt, injection molding, and organic chemistry applications are removed, leaving lab equipment ultraclean for critical testing This cost-effective, fully automatic method saves time and creates a safer, more efficient lab environment. Costs and risks of hazardous waste handling and disposal, glass breakage, and labor are reduced or eliminated. Lab technicians no longer need to rely on scraping, wire brushing, or hand heating to clean bitumen or other organic residues from the glassware. Operators can simply place everything in their pyrolytic oven, press start, and allow the machine to do the work. This not only reduces mess, but saves time and creates a safer, more efficient lab environment. Maximum oven temperature is 482°C and cleaning temperatures range from 426°C to 482°C to burn off organic contaminants, leaving behind only carbonized residue, which can be easily removed. Technical Specification: • Cleaning temperature : 800 – 900°F • Safety : High Temperature Cut-Off System • Power Supply : 240 V, 50 Hz., Single Phase • Min. Overall Dimensions in Inches (L x W x H): 31 x 37 x 60 • Min. Overall Dimensions : 800 X 800 X 1600(L X W X D) mm • Weight : 250 Kg Approximately, LATERAL EXTENSOMETER - DIGITAL This apparatus is used for determination of the strain and deformation characteristics of cement concrete cylindrical specimens of 150 mm dia x 300 mm length., SHRINKAGE BAR MOULD - 25 X 25 X 250 MM SINGLE COMPARTMENT Supplied with a pair of smooth reference Point Pins, as per IS:IS:10086, IS: 4031, ASTM C 151 . Effective Gauge Length 250mm ± 2mm, single Mould compartment, LENGTH COMPARATOR WITH DIGITAL DIAL GAUGE - IS 4139, INFRA RED MOISTURE BALANCE - MOC63U Technical Specification • Capacity : 62g • Minimum readability : 0.001g 0.01/0.1% (Selectable) • Repeatability : 0.15% (2g) 0.05% (5g) 0.02% (10g) • Drying heater : Straight type halogen heater • Power : 400w • Temperature range : 50- 200°C (1°C increments) (There is a time restriction when exceeding 180°C) • Display : LCD with backlight • Pan Size : 95mm dia • Dimensions : 202 × 336 × 157 mm (W×D×H) • Weight : 4kg • Measurement modes : Standard (Easy start/Automatic end/Timed end) Rapid drying (Easy start/Automatic end/Timed end) Slow drying (Easy start/Automatic end/Time • Timer setting : 1120 minutes or continuous (max 12 hours) • Interface : RS 232C (9 pin connector) I/O port USB port • Internal Data Memory : 100 • Measurement conditions data memory : 10 Total Quantity : 1. Last date of submission for this tender is 2024-06-19. This is a Moisture Balance tender in Dharwad, Karnataka