Translational Health Science And Technology Institute

Translational Health Science And Technology Institute has published Tender For Design, Fabrication, Supplying And Fixing Of Laboratory Furniture For Dr. Jayanta Bhattacharya Lab At 1St Floor, Thsti Building At Ncr Bsc Faridabad.; Fabrication, Supply And Installing Of Dual Sided Island Work Bench Of Required Size, Made Up Off 1Mm Thick Gi Sheet As Per Is 277 Standards With Highly Corrossion Resistant Epoxy Powder Coated With 70-80 Microns Thickness Including Granite Top Of 18Mm Thick, 3 Tier Reagent Rack With 2 Adjustable Shelves And Overhead Storage Cabinet With Sliding Glass Door Openable Both Sides, With Pp Sink, And Accessories. Combination Of Door Drawer Cabinets, Legspace & All Required Covering Panels As Per The Approved Drawing, Specification And Direction Of Engineer-In-Charge: ( Specification Listed Below ) Specification:-1. Reagent Rack:- 3 Tier Structure With 2 Adjusable Shelves Of Width 440Mm And Height 1200Mm And Length As Per Drawing And Sefa Specification - 03Nos2. Overhead Storage:- Sliding Glass Door And Vertical Partitionand 1 Adjustable Shelve Of Width 450Mm And Height 450Mm And Length As Per Drawing And Sefa Specification - 03 Nos. 3. Under Bench Module:- Completely Made Of 1 Mm Gi Sheets As Per Is 277 Standards. Having 1 Drawer Unit & 2 Shutter With Shelf With & Inbuilt Plinth With Level Bolts Height 105 Mm. The Sound Deadening Plastic Bumpers To Be Used While Closing The Shutter. The Entire Module Is Made Up Of Gi Panels And Are Bolted / Riveted For Achieving Maximum Strength With High Corrosion Resistance. The Shutters Or Doors Are Mounted To The Modules By Hinges Which Are Openable To 95 Degrees. Drawers Are Mounted With The Ball Bearing Based Telescopic Slides Which Are Sturdy & Able To Take Load Up To 30Kg. Provision Of Lock And Key Shall Also Be There In The Scope. Width 750Mm, 775 Mm Standing Height And Length As Per Layout- 06 Nos.4. Sink Unit:- Big Pp Sink - 600L X 450W X 300D Mm With Hand Held Dual Eye Wash, Three Way Water Tap -Gooseneck Type, Peg Board Big Size: 750Mm L X 750Mm H ( 33 Pegs. ) With Ss 304 Grade Collection Tray Including All Cpvc Water Connection From Source With Pvc Drainage Line, 2 Shutters Sink Unit ( Island Table ) With Both Side Pp Waste Bin Drawer Type Having Waste Flap - 1800 Mm ( L ) X 750 Mm ( D ) X 775 Mm ( H ) & Inbuilt Plinth With Level Bolts Height 105 Mm - 01 Nos5. Module Base Plinth: - Storage Modules Are Rest On The Plinth Of 105Mm Height. Level Adjustment Bolts Are Fitted Below The Plinth. Optionally Front Of The Plinth Are Covered With Black Rubber Skirting And Corners Are Finished With Molded Clips. The Rubber Skirting Is Fixed With The Plinth By Screws.6. Knee Space Area: - Foot Rest With Openable Back Cover Panel. It Must Be Adjustable + 100 Mm. Instrumentation And Sitting Area Knee Space Need To Be 750 Mm.7. Closing Panel:- All The Gaps In The Leg Space End Support, Back Panel, Filler Panel And All Other Gaps Shall Be Closed With The Closing Panel. Leg Space-750 Mm ( L ) With Foot Rest And Back Panel ( Size:-750 Mm ( L ) X 775 Mm ( H ) ) - 06Nos Andleg Space End Support With Sandwich Pattern Gap Closing Panel ( Table 900Mm H ) - 01Nos8. Powder Coating: - Complete Module & Frame Work Is Processed With Multi Tank Pre- Treatment And Finished With Highly Corrosion Resistant Kansai Nerolac / Equiv Epoxy Powder Coating With 70 - 80 Microns’ Thickness. 9. Work Top: - Made Of 18 Mm Thick Jet Black Granite Top With Chamfer Moulding At The Front & Groove At The Bottom To Avoid Chemical Spillage On The Modules. Worktop Will Be Fixed With The Module By Foam Tape, All Joints Are Sealed Thru Epoxy Sealant. Marine Grade Plywood Bed If Needed Would Be Provided.10. Electrical Trunking:- Rectangular Electrical Trunking Under The 1St Tier Of Reagent Rack With Wiring ( 2.5 Sq.Mm Frls ) With Elect. Socket With Piano Switch 6 / 16 Amp With Wiring ( 2.5 Sq.Mm Frls ) - 18Nos. 11. Lighting:- Provision Of Appropriate Led Tubelight 40 Watt Of Approved Make Shall Be Fixed.Size:- Island Bench ( With Reagent Rack & Overhead Storage ) -Length 5340 ± 50Mm, Width 1800 ± 15Mm & Height900 ± 25Mm ( Excluding Worktop ) 2 Fabrication, Supply And Installing Of Dual Sided Island Work Bench Of Required Size, Made Up Off 1Mm Thick Gi Sheet As Per Is 277 Standards With Highly Corrossion Resistant Epoxy Powder Coated With 70-80 Microns Thickness Including Granite Top Of 18Mm Thick, 3 Tier Reagent Rack With 2 Adjustable Shelves And Overhead Storage Cabinet With Sliding Glass Door Openable Both Sides. Combination Of Door Drawer Cabinets, Legspace & All Required Covering Panels As Per The Approved Drawing, Specification And Direction Of Engineer-In-Charge: ( Specification Listed Below ) Specification:-1. Reagent Rack:- 3 Tier Structure With 2 Adjustavble Shelves Of Width 440Mm And Height 1200Mm And Length As Per Drawing And Sefa Requirement - 04 Nos.2. Overhead Storage:- Sliding Glass Door And Vertical Partitionand 1 Adjustable Shelve Of Width 450Mm And Height 450Mm And Length As Per Drawing And Sefa Requirement - 04 Nos. 3. Under Bench Module:- Completely Made Of 1 Mm Gi Sheets As Per Is 277 Standards. Having 1 Drawer Unit & 2 Shutter With Shelf With & Inbuilt Plinth With Level Bolts Height 105 Mm. The Sound Deadening Plastic Bumpers To Be Used While Closing The Shutter. The Entire Module Is Made Up Of Gi Panels And Are Bolted / Riveted For Achieving Maximum Strength With High Corrosion Resistance. The Shutters Or Doors Are Mounted To The Modules By Hinges Which Are Openable To 95 Degrees. Drawers Are Mounted With The Ball Bearing Based Telescopic Slides Which Are Sturdy & Able To Take Load Up To 30Kg. Provision Of Lock And Key Shall Also Be There In The Scope. Width 750Mm, 775 Mm Standing Height And Length As Per Layout - 08 Nos.4. Module Base Plinth: - Storage Modules Are Rest On The Plinth Of 105Mm Height. Level Adjustment Bolts Are Fitted Below The Plinth. Optionally Front Of The Plinth Are Covered With Black Rubber Skirting And Corners Are Finished With Molded Clips. The Rubber Skirting Is Fixed With The Plinth By Screws.5. Knee Space Area: - Foot Rest With Openable Back Cover Panel. It Must Be Adjustable + 100 Mm. Instrumentation And Sitting Area Knee Space Need To Be 750 Mm.6. Closing Panel:- All The Gaps In The Leg Space End Support, Back Panel And All Other Gaps Shall Be Closed With The Closing Panel. Leg Space-750 Mm ( L ) With Foot Rest And Back Panel ( Size:-750 Mm ( L ) X 775 Mm ( H ) ) - 06Nos Andleg Space End Support With Sandwich Pattern Gap Closing Panel ( Table 900Mm H ) - 01Nos7. Powder Coating: - Complete Module & Frame Work Is Processed With Multi Tank Pre- Treatment And Finished With Highly Corrosion Resistant Kansai Nerolac / Equiv Epoxy Powder Coating With 70 - 80 Microns’ Thickness. 8. Work Top: - Made Of 18 Mm Thick Jet Black Granite Top With Chamfer Moulding At The Front & Groove At The Bottom To Avoid Chemical Spillage On The Modules. Worktop Will Be Fixed With The Module By Foam Tape, All Joints Are Sealed Thru Epoxy Sealant. Marine Grade Plywood Bed If Needed Would Be Provided.09. Electrical Trunking:- Rectangular Electrical Trunking Under The 1St Tier Of Reagent Rack Electrical Trunking Ofwith Wiring ( 2.5 Sq.Mm Frls ) With Elect. Socket With Piano Switch 6 / 16 Amp With Wiring ( 2.5 Sq.Mm Frls ) - 24 Nos. 10. Lighting:- Provision Of Appropriate Led Tubelight 40 Watt Of Approved Make Shall Be Fixed.Size:- Island Bench ( With Reagent Rack & Overhead Storage ) -Length 5310 ± 50Mm, Width 1800 ± 15Mm & Height900 ± 25Mm ( Excluding Worktop ) 3 Fabrication, Supply And Installing Of Single Side Sitting Bench Of Required Size, Made Up Off 1Mm Thick Gi Sheet As Per Is 277 Standards With Highly Corrossion Resistant Epoxy Powder Coated With 70-80 Microns Thickness Including Granite Top Of 18Mm Thick. Combination Of Door Drawer Cabinets, Legspace & All Required Covering Panels As Per The Approved Drawing, Specification And Direction Of Engineer-In-Charge: ( Specification Listed Below ) Specification:-1. Under Bench Module:- Completely Made Of 1 Mm Gi Sheets As Per Is 277 Standards. Having 1 Drawer Unit & 2 Shutter With Shelf With & Inbuilt Plinth With Level Bolts Height 105 Mm. The Sound Deadening Plastic Bumpers To Be Used While Closing The Shutter. The Entire Module Is Made Up Of Gi Panels And Are Bolted / Riveted For Achieving Maximum Strength With High Corrosion Resistance. The Shutters Or Doors Are Mounted To The Modules By Hinges Which Are Openable To 95 Degrees. Drawers Are Mounted With The Ball Bearing Based Telescopic Slides Which Are Sturdy & Able To Take Load Up To 30Kg. Provision Of Lock And Key Shall Also Be There In The Scope. Width 450 Mm, 775 Mm Standing Height And 675 Mm Sitting Height And Length As Per Layout - 02 Nos.2. Module Base Plinth: - Storage Modules Are Rest On The Plinth Of 105Mm Height. Level Adjustment Bolts Are Fitted Below The Plinth. Optionally Front Of The Plinth Are Covered With Black Rubber Skirting And Corners Are Finished With Molded Clips. The Rubber Skirting Is Fixed With The Plinth By Screws.3. Knee Space Area: - Foot Rest With Openable Back Cover Panel. It Must Be Adjustable + 100 Mm. Instrumentation And Sitting Area Knee Space Need To Be 750 Mm.4. Closing Panel:- All The Gaps In The Leg Space End Support, Back Panel And All Other Gaps Shall Be Closed With The Closing Panel. Leg Space-600 Mm ( L ) With Foot Rest And Back Panel ( Size:-600 Mm ( L ) X 675 Mm ( H ) ) - 01 Nos 5. Powder Coating: - Complete Module & Frame Work Is Processed With Multi Tank Pre- Treatment And Finished With Highly Corrosion Resistant Kansai Nerolac / Equiv Epoxy Powder Coating With 70 - 80 Microns’ Thickness. 6. Work Top: - Made Of 18 Mm Thick Jet Black Granite Top With Chamfer Moulding At The Front & Groove At The Bottom To Avoid Chemical Spillage On The Modules. Worktop Will Be Fixed With The Module By Foam Tape, All Joints Are Sealed Thru Epoxy Sealant. Marine Grade Plywood Bed If Needed Would Be Provided.7. Electrical Trunking:- Triangular Electrical Trunking Of120mmd X 120Mmh With Wiring ( 2.5 Sq.Mm Frls ) With Elect. Socket With Piano Switch 6 / 16 Amp With Wiring ( 2.5 Sq.Mm Frls ) - 07Nos. Size:-Sitting Bench -Length 4020 ± 50Mm, Width 750 ± 15Mm & Height800 ± 25Mm ( Excluding Worktop ) 4 Supplying And Replacing Of Damaged Mineral Fibre Beveled Tegular Edged Ceiling Tiles 595 X595mm, 16 Mm Thick With Bio-Block Conforming To Iso 5 ( Class 100 ) Specifications.. Last date of submission for this tender is 2023-11-30. This is a Fabrication Work tender in Faridabad, Haryana