Haryana Power Generation Corporation Limited

Haryana Power Generation Corporation Limited has published Supply Of Spares Of Coal Mills (Hp-1103) To Rgtpp, Khedar, Hisar On Annual Contract Basis. , Supply Of Spares Of Coal Mills (Hp-1103)To Rgtpp Khedar Hisar On Annual Contract Basis, For Qty & Detail Please Refer Annexure-1 Of Nit In Detail , Air Restriction Ring Large Size (Length Approx. 1800Mm, Width 60Mm, Thickness 28Mm)(1 Set= 8 Nos.) , Air Restriction Ring Small Size (Length Approx. 1800Mm, Width 35Mm, Thickness 28Mm)(1 Set= 8 Nos.) , Shroud Plate1360x120x10 (1 Set= 8 Nos.) , Vane Wheel Segment For Coal Mill (Hp-1103), (1 Set= 8 Nos.) , Roller Retainer Ring For Coal Mills Moc: 16Mn , Mill Bowl Hub Clamping Ring Moc- 16 Mn (1 Set=4 Nos.) , Scrapper With Liner Plate Long, Moc:Is 1030, Gr-Ii, (Cast Steel) Moc Of Linear Iss 276 Astm Grade-3 , Scrapper With Liner Plate, Short, Moc:Is 1030, Gr-Ii, (Cast Steel)Moc Of Linear Iss 276 Astm Grade-3 , Journal Housing Liner Upper, Moc: Cast Steel As Per Is 1030 Grade-2 , Journal Housing Guard/Liner Lower, Moc- Ss-304 , Coal Mill Coupling Complete K3741.18.0 , Tapper Bolt With Ss Washer & Nuts For Motor Coupling , Locking Plate Of Grinding Rolls L=274Mm, T=32Mm , Journal Bearing Keeper Moc: En24 Forged, Od-456Mm, Id-105Mm, Pcd-232 Mm, 8 Nos. Of Holes Of Size M32, Thickness-40Mm , Wear Resistant Weld Overlay Plate With Carbide Layer Of 6Mm For Coal Mill, Carbide Layer On Inner Side Of Curved Portion Dimensions-Height:1500Mm, Width-1000Mm, Thickness-10Mm(1 Set= 6 Nos.) , Ms Flange For Hot Air Diaphragm Moc- Mild Steel, Thickness-10Mm, Id- 805Mm, Od-944Mm, Pcd-890Mm, No. Of Holes-20 Nos. Of Size-M18. , Ventury Outlet For Coal Mill Hp-1103 Moc- Carbon Steel , Filter Disc With Teflon Ring Id: 71Mm, Od: 155Mm, T: 8Mm, Media: Ss35 Um {Required For Round The Clock Filtration Of Lube Oil (Servo Mesh Xp-320) Of Coal Mills Hp-1103} , Ventury Outlet Collar For Coal Mill Hp-1103 Moc- Carbon Steel , Cover For Hot Air Diaphragm, Moc- Al Sheet, 2Mm, Od-900Mm , Ventury Vane For Coal Mill, Hardness= 60-62 Hrc , Hard Thickness=15Mm (1 Set=4 Nos.) , Seal Wear Ring Of Coal Mill Journal Assembly Shaft, Od-470 Mm, Id-390 Mm, Width- 102 Mm, Moc-Ss304 , Journal Housing Seal Cover For Journal Assembly Of Coal Mills Moc:Is1020 Cast Steel/En24 , Wearable Adjustable Shrink (Adjustable Orifice) For Coal Mill Hp-1103, Coal Pipeod-710Mm, Model-Smk Type-B {Wearable Adjustable Shrink To Be Supplied With 2 No. Extra Flange For Connection/ Installation With Pc Pipe} , Mill Discharge Valve (Mdv) Without Power Cylinder For Coal Mills Hp-1103 , Feeder Outlet Gate Without Actuator , Mill Body Deflector Support Plate Ms, 1 Set= 3 Nos. , Roller Liner Device For Coal Mill , Separator Body Liner-I, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Ii, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Iii, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Iv, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-V, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Vi, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Vii, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-X, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Xi, Moc: Ni Hard Along With Weld Plugs , Separator Body Liner-Xii, Moc: Ni Hard Along With Weld Plugs , Liner Rld Type-I, Moc: Ni Hard Along With Weld Plugs , Liner Rld Type-Ii, Moc: Ni Hard Along With Weld Plugs , Liner Rld Type-Iii, Moc: Ni Hard Along With Weld Plugs , Liner Rld Type-Iv, Moc: Ni Hard Along With Weld Plugs , Liner Rld Type-V, Moc: Ni Hard Along With Weld Plugs , Vane Of Deflector Door Moc- High Alloying Wear Resistance Material Hardness:- 55-62 Hrc (1 Set=40 Nos.) , Seals Of Hot Shut Off Gate- L2000 Mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Seals Of Hot Shut Off Gate-L1800mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Seal Air Assembly For Gear Box For Coal Mill , Pyrite Chute/ Tramp Iron Spout For Coal Mill Hp-1103 Moc- Ss-304 , Lower Skirt For Coal Mill Hp-1103 (Moc:Carbon Steel) 1 Set= 4 Nos. , Idler Roller For Rc Feeder Model:Cs2036, 1 Set=12 Nos. , Bushing For Rc Feeder And Coal Millgt1651807 , Feeder Outlet Hopper Of Rc Feeder , Clean Out Conveyor Chain With Scrapper, Moc: Cast Alloy Steel, Pin: En-08, 1 Set= 82 Pieces, 72 Chain Links And 10 Chain Scrapper , Expansion Bellow For Pulverized Fuel Piping Specification: 04 Congulations (Ss 304, Thickness-2Mm). Medium: Coal+ Hot Air. Maximum Air Flow Per Mill:125 Tonne Per Hour. Pipe Od-710Mm, Thickness Of Connection End-16Mm (Mild Steel). Position Of Fitment: Horizontal. , Erw Coal Pipe, Grade-Api 5L, Od Of Pipe-710Mm, Thickness Of Pipe-16Mm , Bearing Housing For Rc Feeder And Coal Mill Gt1651907 , Eccentric Bearing Housing For Rc Feeder And Coal Mill , L-150 Coupling With Rubber Spider , Journal Assembly Top Cover Plate For Coal Mill Hp-1103 , Drive Proket Shaft For Feeder Outlet Gate , Gear For Feeder Outlet Gate , Gear For Coc Gearbox Nde , Helical Gear Both End Set For Coc Gearbox , Shaft For Coc Chain Reducer Gearbox , Coc Coupling , Helical Gear Small De For Rc Feeder Gearbox , Helical Gear Nde For Rc Feeder Gearbox , Gear For Coc Gearbox De , Cover For Coal Feeder Outlet Gate, Gt1620607 , Reducer Body For Coal Feeder Outlet Gate, Gt1621007 , Reducer Cover For Coal Feeder Outlet Gate, Gt1621207 , Cover For Coal Feeder Inlet Gate, Gt161-C0607 , Reducer Body For Coal Feeder Inlet Gate, Gt161-C0707 , Reducer Cover For Coal Feeder Inlet Gate, Gt161-C0907 , Tube Bleeder Housing For Coal Feeder, Gt1652907 , Tube Bleeder For Coal Feeder, Gt1653007 , Coal Feeder Inlet End Door (Complete) , Coal Feeder Discharge End Door (Complete) , Trunion Bushing Journal K3741.14.4.0 , 600 Mw Id-216 Mm, Od-254 Mm, Length – 325 Mm, Moc Of Tube: Seamless Asme Sa 106 Gr. B, Moc Of Rubber:- Ethylene Acrylic Elastomer Of Shore Hardness 50-55 A. Last date of submission for this tender is 2025-09-02. This is a Coal Mill tender in Hisar, Haryana