Department Of Employment And Training

Department Of Employment And Training has published Bids Are invited for Crimping Tool - 16 sq mm to 95 sq mm , Wire Cutter and Stripper - 150 mm , Contactor and auxiliary contacts - 3 phase 415 volt 32 Amp with 2 NOand 2 NC , Hydrometer - good quality , Hand Drill Machine - 0 to 6 mm capacity , Knife Switch DPDT - 16 Amp , Knife Switch TPDT - 16 Amp 440 V , Earth Plate - 60cm X 60cm X 3.15mm CopperPlate 60cm X 60cm X 6mm GI Plate , Earth Electrode - Primary Electrode 2100x28x3.25mmSecondary Cu Strip 20x5mm , MCCB - 100Amps Triple pole , ELCB - 25Amps double pole and In 30 mA , RCCB - 25Amps and double pole , Rheostat Sliding type - 2 Amp 0 to 1 Ohm , Various type lamp - Halogen Incandescent Lamp Fluorescent tube HP mercury vapor Lamp High-pressure sodium Lamp Low-pressure sodium Lamp LED Lamps , Bus bar with brackets - 1 mtr each , Rubber mat - 2 mtr x 4 mtr x 1 inch size , Digital Multi Meter - DC 200mv to 1000v 0 to 10A and AC200mv to 750v 0 to 10A resistance 0 to 20M and 3.5 digit , Milli Voltmeter - entre zero analog portable box type housed in Bakelitecase 100 to 0 to 100 mV , Ammeter MC analog - 0 to 500 mA 0to5 A 0to25 A , AC Ammeter MI - zero to 1 A zero to 5 A zero to 25 A , Digital Wattmeter - 230 V 1 KW 50 Hz , Power Factor Meter Digital - 440 V 20 A Three Phase portablebox type , Magnetic Flux Meter - 0 to 500 tesla , Tachometer - Analog Type 10000 RPM , Megger - Analog 500 V , 3 point DC Starter - For 2.5 KW DC motor , 4 point D.C. Starter - For 2.5 KW DC motor , AC Starters - Resistance type starter star delta soft starter , Function Generator - 2 to 200 KHz Sine SquareTriangular 220 V 50 Hz Single Phase , Soldering Iron - Temperature controlled 50 Watt 230 Volt , Discrete Component Trainer - Discrete Component for diode andtransistor circuit with regulatedpower supply +5 0- 5 V +12 0-12 V , Smart Meter - 1 Phase Smart Energy Meter 3 Phase Smart Energy Meter , Measuring Steel Tape - 5 meter , Combination Plier Insulated - 200 mm , Screwdriver Insulated - 4mm X 150 mm Diamond Head , Screwdriver Insulated - 6mm X 150 mm , Electrician screwdriver - thin steminsulated handle 4mm X 100 mm , Heavy Duty Screwdriver insulated - 5mm X 200 mm , Electrician Screwdriver - thin steminsulated handle 4mm X 250 mm , Punch Centre - 9mm X 150 mm , Knife Double Bladed Electrician - 100 mm , Neon Tester - 500 V , Steel Rule - Graduated both in Metricand English Unit 300 mm with precision of 1/4 mm , Hammer cross peen with handle - 250 grams , Scissors - 25 cm , Garment Hangers - good quality , Seam Ripper - good quality , Tailor s Card Scale Triangular - good quality , Tailors Square - Plastic , French Curve - Set of three , Thread Cutter - 24 INCH , Scale plastic - good quality , MEASURING TAPE - 150CM , Multi meter - 0 to 5 100 200 500 milli-amperes0 to 150 300 600 V AC or DC , Ammeter Mi - 0 to 30 Amp panel board , Ammeter MC - 0 to 500 mA , Solid State Solar Based Single Phase Energy Meter Bidirectional - 5 to 30 Amps 240 Volts , Ammeter MI - 0 to 5Amp Panel board type , Ammeter MI - 0 to 10 Amp panel board mounting type , Ammeter MC Centre zero - 5 to 0 to 5 Amp , Magnetic Flux Meter - 0 to 500 tesla , Lux meter - lux meter LCD read out 0.05 to 7000lumens with battery , Hydrometer - good quality , Hydraulic crimping tool - for UG cablecrimping with bits 20 Sq mm to 250 sq mm , Bar magnet - good quality , Small crimping tools assorted - 10 to 100 mm 5 Nos , Rubber matting - 2 meter x 1 meter x 9 mm , Set of Wall jumper octagonal - 37mm X 450mm and 37 X 600mm , Pliers round nose insulated - 200 mm , Firmer chisel - 1 inch , Gauge wire - imperial stainless steelmarked in SWG and mm Wire Gauge Metric , File flat - 300 mm rough , Pipe vice - Cast Iron with hardenedjaw open type 100 mm , Insulators including hardware fitting - Pin Type and shackle type and egg type andsuspension type , Knife Switch DPDT - 16 Amp , Knife Switch TPDT - 16 Amp 440 V , Bus bar with brackets - 1 mtr each , Electrician Helmet - Yellow Colour , Safety belt - with provision forkeeping tools , Solar Street Light - 12V 75Ah battery 75 Wp solar panel12V 10A dusk to dawn chargecontroller 60 W LED lights and 9 mheight pole all dismountable , Solar Traffic Light - 12V 75Ah battery 75 Wp solar panel12V 10A dusk to dawn chargecontroller 15 W LED lights with suitablecolors and 9 m height pole alldismountable , Solar DC pump - 24V 1 HP , Lead Acid battery 75Ah - 12 V , Solar street light lamp set - 12 V 18 or 24 watts , Steel rule - 300 mm , Terminal screw Driver - 75 mm Connector , Knife Electrician - DB , Hammer Ball peen - 0.25 Kg , Plumb bob - 115 grams , Combination pliers insulated - 200 mm , Try square - 200 mm , Spanner set DE - Set of 6 from 6x7 to 16x7 , Screw driver set set of 5 - 100 to 300 mm , File round 2nd cut - 150 mm , Soldering iron - 60 W 230 V , Steel measuring tape - Pocket type , Bradawl - 150 mm x 6mm square pointed , Set of Rowel punch - 8 10 mm , wooden mallet - 1 kg 75mm x 15mm , Wheostone bridge - good quality , Belt Tensioner gauge - good quality , Different type of Engine Bearing model - good quality , Different type of piston model - good quality , Drill twist various sizes - 1.5 mm to 15 mm by0.5 mm , Growler - good quality , Hacksaw frame - Adjustable 20 to 30 cm , Hammer Mallet - good quality , Hand vice - Up to 37 mm , Injector testing set Hand tester - good quality , Left cut snips - 250mm , Oil Stone - 15 cm x 5 cm x 2.5 cm , Oscilloscope - 20MHz , Dividers with spring - 15 cm , Pliers combination - 20 cm , Spindle key - good quality , Hammer sledge - double faced 4 kg , SS tape - 5 meters flexible in case , Multiangle magnetic clamp set - Metal base 18x10x10 cm , Vernier caliper - 150 mm , Drill twist Taper shank - 8 mm to 20 mm by 0.5 mmHSS , Taps and dies complete set - 5 6 8 10 and 12mm set of 5 , File feather edge smooth - 150 mm , File triangular smooth - 200 mm , File square second cut - 250 mm , File triangular second cut - 200 mm , File half round second cut - 250 mm , File half round bastard - 250 mm , File round bastard - 250 mm , File hand second cut - 150 mm , File card Wire Brush - 3 inch x5 inch size brass or steelwire , Pliers combination insulated - 150 mm , Clamp C - 200 mm , Scraper flat - 150 mm , Scraper triangular - 150 mm , Scraper half round - 150 mm , Power tools for fastening - Capacity 10 to 18mm , Different Profile gauges - Plate type Fordemonstration Metric standard , Knurling tool - Diamond straight andDiagonal good quality , Indexable boring bar with inserts - 1 inch shank , Standard Tap screws - M3 M4 M5 M6 M8 M10 M12 M14 M16 , Lapping plate - Dia 6 inch , Drill gauges - Letter drill gauge A to Z Number drill gauge 1 to 60Metric drill gauge 1.5mm to12.5mm 30 holes , Cast Iron Globe Valve Flanged type - 150NB Class 150 FlangeANSI12 B16.1 , CI Sluice Gate valve flanged type - 150NB Class 150 Flange ANSI125 B16.1 , Stop cock - 25NB 2 way Threaded end , Slip on Forged steel Flange - 150NB ANSI B16.5 Class 150 , Pulleys for V-belt or Flat belt - to fit on 50mm dia Shaftwith key slot , Hollow punch - Straight Shank Hollow PunchSets 5 to 12mm , Bearing extractor - Universal gear puller 2 or 3jaws adjustable , Pulley extractor - good quality , Flat headed hammers with handle. - good quality , Planishing hammer. - good quality , Snip bent Left Cut - 250 mm , Stake hatchet with Leg - 300 X 200 X 20 mm , Arm strong type tool bit holder - Left hand , Arm strong type tool bit holder - Straight , Try Square - 150 mm blade , Scriber - 150 mm , File flat second cut - 250 mm , Hacksaw frame fixed type - 300 mm Total Quantity : 1092. Last date of submission for this tender is 2026-04-15. This is a Cutting Crimping And Punching Tools tender in Vadodara, Gujarat