Indian Institute Of Technology

Indian Institute Of Technology has published Tender For Supplying, Installation, Testing And Commissioning Of Outdoor Feeder Panel For Power Supply To Cits, Central Library And Nearby Areas At Iit Goa.; 1 SITC of Outdoor Feeder Pillar Panel in front of Mahalaxmi Bunglaw (CITS) with IP 55 Protection, made with 14/16 swg powder coated CRCA sheet of approved colour paint by Engineer-in-Charge, Incomer 250 A 36 KA 4P MCCB-1 No; Outgoing 100 A 3P MCCB-3 No, 63A 3P MCCB-3 No; along with LED RYB indicators, Voltmeter,Ammeter,selector switch, necessary rated capacity CTs Accuracy-1,suitable size Aluminium bus bar for phase,neutral,earth bar,busbar supports, spreaders,phase seperator,ventilation louver etc complete with respect to IS 60439 specifications. 2 Supplying and Laying of 1.1 kV, XLPE Armoured LT UG Cable as per IS-1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 3 4 x 16 sq.mm Aluminium conductor Armoured XLPE Cable 4 3½ x 50 sq.mm Aluminium conductor Armoured XLPE Cable 5 3½ x 95 sq.mm Aluminium conductor Armoured XLPE Cable 6 4 x 16 sq.mm Copper conductor armoured XLPE cable 7 Supply, installation, testing, and commissioning of three phase, 4 wire KWh meter LCD type,Acc.class 0.5s,50 Hz CT operated MRT tested energy meter for load capacity 20-100A, displaying parameters such as date, time, voltage, current, kWh, kVarH, kVAh etc. enclosed inside a powder coated metal enclosure of suitable size inside the feeder and connecting with wires coming from CTs etc., Test certificate must be submitted before installation complete in all respects as required.Make: L&T,Secure,HPL, GED approved makes 8 Supply, Installation, testing and commissing of CTs of following ratios tested by Goa Electricy Department, Note: Test certificate must be submitted before installation including necessary wiring for connecting metering unit to CTs 9 100A/5A , Set of Three Ring type CTs 10 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulatedand PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 11 4 X 16 sq. mm (28mm) 12 3½ X 50 sq. mm (45mm) 13 3½ X 95 sq. mm (45mm) 14 Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials forfollowing size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required 15 4 X 16 sq. mm 16 3½ X 50 sq. mm 17 3½ X 95 sq. mm 18 Disconnection and removing of old cable from existing panel to new feeder pillar panel 19 Providing MS angle Structural steel work with MS Angle of 50x50x5mm dimensions in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a primercoat of approved steel primer all complete for Feeder Pillar Panel Base angle with supports 20 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 21 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) 22 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 23 Supply and fixing Padlocks for existing feeder panels as per the site requirement . Last date of submission for this tender is 2025-08-18. This is a Electrical Panel tender in Goa, Goa