Public Works Department

Public Works Department has published Repair and renovation of many rooms including basement painting of boundaries, changing of Alluminium window etc and other miscellaneous items at Banga Bhawan, 3 Hailey Road, New Delhi 110001 under Banga Bhawan Sub- Division during the year 2025-2026- 1 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 2 Dismantling alluminium gypsum partitions doors windows fixed glazing and false celling including disposal of unserviceable material and stacking of serviceable material with in 5o mtr lead as directed by E-in-c 3 Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excludingcost of chipping over concrete surface] (i) With 1:6 cement mortar (a) 15 mm thick plasterout side boundary wall 4 Supplying, fitting and fixing boiling water proof block board conforming toIS:1659-1990 conforming to IS:848-1974 of approved make and brand, fitted andfixed as per design as per direction of Engineer-in-charge. [Excluding the cost ofsupporting frame work and teak wood batten/Lipping].In Ground Floor(i) 19mm rooms 5 Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 asper approved make, brand, finish and thickness with fitting, fixing the same onParticle/MDF / Ply Boards with recommended / approved adhesive with properclipping the sides for better attachment as per direction of Engineer-incharge.The rate includes the cost of labour, adhesive and all incidental chargesthereof.In ground floorGlossy/Matt/Suede excluding surface texture or metallic lustre.(i) Thickness of laminate 1.5mm 6 Providing and Fixing false celing at all height including providing and fixing of frame work made of special sections power presses from Ms sheet and galvanized with coatngof 150 gms/sqm both side inclusive as per IS 277 and consisting of angle cleats of size 25mm wide x 1.6 mm thick with flanges of 27mm and 37 mm at 1200mm c/c one flange fixed to the ceilling with dash fastner 12.5 dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x.50 mm of required running at the spacing of 1200 mm centre to center to which the celling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm at 450 mm centre to centre shall be fixed in direction perpendicular to GI intermidiate channels with connecting clips made out of 2.64 mm dia x 230 m long gi wire at every junction as directed by E-in-c 7 Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, ground Basement 8 Apply in g Interiorgrade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/Acrylicemulsionpaint including scrapingandpreparing thesurfacethroughly,completeaspermanufacturersspecificationand as per direction of the EIC. (In Ground Floor)(a) One Coat i) Water based interior grade Acrylic Primer 9 (a) ApplyingExteriorgradeAcrylicprimerofapprovedqualityandbrand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsionpaint includingscrapingandpreparingthesurfacethroughly, completeaspermanufacturersspecificationandasperdirectionofthe EIC. In Ground Floor: (a) One Coatboundary of wall 10 on 5th floor slab 11 Rendering theSurfaceofwalls andceilingwithWhiteCement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) 12 ApplyingAcrylicEmulsionPaint of approvedmakeandbrandonwalls andceilingincludingsandpaperinginintermediatecoatsincludingputty (to be done under specific instruction of Superintending Engineer) : (Two coats) rooms 13 a.ProtectiveandDecorativeAcrylicexterioremulsionpaintofapproved quality, as permanufacturers specification and as per direction of Engineer-in-Chargetobeappliedoveracrylicprimerasrequired.The rate includes cost ofmaterial, labour, scaffoldingandall incidental charges but excluding the cost ofprimer. In Ground floor (Two Coat) a) Normal Acrylic EmulsionFor boundary wall, 5th floor roof 14 b. on 5th floor 15 supplying fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of CI brackets b. sink with drain board 1050mm x 450mm x 180mm 16 Supplying profiles of required section made of Aluminium Alloy Extrusionsconforming toIS:732-1983andIS:1285-1975;Annodized (withrequiredfilmthicknessandspecifiedcolour/natural)mattfinished conformingtoIS:1868-1983forfabricationofcompositdoor, sliding& casement windows, partitions, formed of basic sections of any ISI embossed/certifiedmakeandbrandasperdirectionofEngineer-InCharge. (Payment will be made on finished length of the work) room 709,501.303,219 17 top and side frame 18 Bottom & Top member. 19 Style side member. 20 Interlock member 21 Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:(A) Glazedaluminiumslidingwindowsmadeofextrudedandannodized alloyaluminiumsectios, fabrications, includingcuttingtopropershape andsize,drillingandaligningofwindowshutterframefittedwithinbuilt lockingarrangements,slidingrollersandothernecessaryfittings,fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing inbetweenwindowframeandmasonrywork (walls, column, beam.lintelsetc.)aswellasbetweenglassandshutter frame for fixing glassandPolysulphidesealantandinbetweenshutterandwindowframe wherenecessary includingcutting torequisitesizeand fixingglassas per drawing, specification and direction of EIC. Therate includes thehirechargeof all toolsandplants, includingall incidentalcharges,adhesive, joineriessuchasscrew,cleatangleetc.but excluding the cost of extruded aluminiumsections, glass, neoprene / EPDM gasket, locking arrangement and rollers. A. ii) 3/4 track sliding winow 22 B. ii) 3/4 track sliding winow 23 c. ii) 3/4 track sliding winow 24 D ii) 3/4 track sliding winow 25 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. i)4mm thick clear glass. 26 SupplyingEPDMgusketofapprovedmakeandbrand asperdirectionof Engineer in charge. i)For sliding windows a) T shaped EPDM gasket for frames. 27 SupplyingPVCrollers forslidingwindowsasperdirectionofEngineer in charge. 28 Supply of chromium plated over brass overhead square shower head with revolving joint having waterfalls head 200mm x 200mm and 13 mm thick with 450mm long square Arm of approvef make equivalent to model no Gx Globex make or similar brand as per direction of EIC equivalent code MOR 1160 29 Supplying fitting and fixing bib cock or stop cock d. i. chromium plated angular stop cock with wall flange equivalent to code no 5053 and model Florentine of jaquer or similar brand 30 Anodised aluminiumbarrel / tower / socket bolt (full covered) of approved manufactured fromextrudedsectionconforming to I.S. 204/74 fittedand fixed with cadmium plated screws:(vi) 200mm long x 10mm dia. bolt. 31 Supplying fitting and fixing alloy iron with brass spindle bib cock/stop cock of aapproved brand and make spray painted and tested to 21 kg 32 CP wall mixture without spout but with provision for connection to telephone shower and exposed pipe for overhead shower equivalent to code no 5215 and model Florentine of jaquer or similar brand . Last date of submission for this tender is 2025-09-08. This is a Building Work tender in Banga, Delhi