Department Of Science And Technology

Department Of Science And Technology has published Supply Of Pharmacy Lab Equipment And Furniture Items In The Premises Of Muzaffarpur Institute Of Technology-01 Fume Hood 1. Floor mounted Fume Hoods should be designed and manufactured according to ASHRAE 110-1995 guidelines for Exhaust and Containment. 2. Dimensions: (1800 L X 900 B X 1500 H) MM 3. Dimensions of the Base: (1800 L X 900 B X 900 H) MM 4. Material of construction Galvanized Iron 1.00 /1.2mm thick construction. 5. Internal finish should have Chemical Resistant Laminate (CRL) 6 mm thickness., while the external finish should be of powder coating of Epoxy Polyester. 6. Combination Sash made of See Through Toughened Glass (Vertical riging/Horizontal Sliding in Metal Powder Coated Frame). 7. Work Top should have Jet Black Granite Work Top 18 thick. 8. 200 x 100 mm Cup Sink made of PP fixed on work Top with Drawing Line up to two-meter length to nearest drawing point. 9. Fume Hood internal single-phase wiring and termination on the top 10. Three nos. of utility connections including Remote valves in brass (Air, CW-IN & CW-OUT, Vacuum) with PU Connection terminated Bottom of Hoods. 11. Butterfly Valve for Individual FH control. 12. Bottom Storage Cabinets with 2 doors (one will have shelf and one below drip cup without shelf) made of GI epoxy powder coated with internal lining for chemical /acidic containers/bottles which not required exhaust during non-working hours. 13. Direct driven PP FRP centrifugal blowers of capacity (suitable cfm for cluster/single) for outdoor use with MOTOR GUARD/Whether Cowl/with motor (one HP TEFC Foot mounted 3Phase 50Hz, 415 Volts) for outdoor application. Blower and Ducting 1. Blower with Motor: Centrifugal With 1800 CFM TEFC1440 Rpm 3 Phase Standard Make NFLP Motor 2. Ducting for Fume Hood PP/PP-FRP ducting using 2.5/3mm thick PPGL sheets 3 mm thick FRP lining using isothelic resin including flanges & bends, gasket, inside lab duct support includes threaded rod, clamps, anchor fasteners, washer nuts and bolts.at least 25 squares meter Sink Table 1. 950L x 750B x 900H mm 2. Bottom Arrangements Base Unit for Sink: 2 Door -900 mm 3. PP Sink of Size: 600X450mm 4. Two-way water tap Blank Paneling Jet Black Granite Work Top of 18 ± 1 mm thick 2 Pharmaceutical Chemistry-II Lab Furniture 1. Granite worktop (18±1) mm thick jet-black polished granite with fully moulded and polished edges 2. Material of construction should be electro galvanized iron (GI) 3. Internal & External finish should have epoxy powder coating 4. Total Dimension 13763 (L) x 750(B) x 900(H) (as per attached design) 5. Under bench modules of length (900±5 mm) with 2 drawer & 2 shutters with lock 6. Under Bench Modules L (600mm) with drawer with lock 7. Under Bench Modules L (466mm) with drawer with lock 8. Electric Point 5/15 amps sockets (North-west/Anchor/Havel’s) pedestal box 9. Corner Table 1050 x1050 x 900 mm with granite top with sink and two-way tap 10. Service dropper GI make ceiling drop 200 x 2400 mm C-Frame Total Dimension 5822 (L) x 1500(B) x 900(H) mm 1. Under Bench Modules of Length (900 mm) with 2 drawer & 2 shutters with lock 2. Electric Point 5/15 amps sockets (North-west /Piano) pedestal box 3. Reagent racks (4) 4. Service dropper GI make ceiling drop 200 x 2400 (mm) 3 Microbiology Lab Furniture 1. Granite worktop (18±1) mm thick jet-black polished granite with fully moulded and polished edges 2. Material of construction should be electro galvanized iron (GI) 3. Internal & External finish should have epoxy powder coating Total dimension (in mm) 8450 (L) x750 (B) x 900(H) (as per attached design) 4. Under Bench modules of 600 mm length with drawer and lock 5. Under Bench modules of 466 mm length with drawer and lock 6. Electric point 5/15 amps sockets (North-west/Anchor/Havel’s) pedestal box 7. Service Dropper GI make ceiling drop 200x2400 8. Corner table 550 x 450 x 350 mm with granite top with sink and one way Tap 4 Biotechnology Lab Furniture 1. Granite worktop (18±1) mm thick jet-black polished granite with fully moulded and polished edges 2. Material of construction should be electro galvanized iron (GI) 3. Internal & External finish should have epoxy powder coating Total dimension (in mm) 11075 (L) x 750 (B) x 900(H) (as per attached design) 4. Under Bench modules of 600 mm length with drawer and lock 5. Under Bench modules of 466 mm length with drawer and lock 6. Electric point 5/15 amps sockets (North-west/Anchor/Havel’s) pedestal box 7. Service Dropper GI make ceiling drop 200x2400 8. Corner table 550 x 450 x 350 mm with granite top with sink and one way Tap . Last date of submission for this tender is 2025-01-17. This is a Laboratory Equipment tender in Muzaffarpur, Bihar