Central Agricultural University

Central Agricultural University has published Purchase Of Steam Distillation Purchase Of Steam Distillation , Purchase Of Steam Distillation Unit , Distillation Still- Material S.S.-304, Batch Capacity 100 / 125 ( + ) Kgsgreen Citronella / Lemon Grass ( The Distillation Still Will Contain:- A. Lid ( Top Cover Of Doomed Shaped ) With Lifting Arrangement For Feeding B. Distillation Still Will Be Fabricated By 2.5 Mm Thick S.S. 304 Sheet And Lid By 1.5 Mm Sheet. Height 1000 Mtr And Dia 860 Mm C. Still Tilting Mechanism For Discharging With Necessary M.S. Shaft, Gear Drive ( Cast Iron Worm And Worm Wheel ) , Cast Iron Block Bushing And Tilting Bevel Pinion / Gear Capable Of Withstand The Heat And Load During Operation And Tilting Operation D. 270 Mm Dia ( 30 Teeth ) Cast Iron Wheel Pinion And 85 Mm Worm Will Be Fitted For Tilting Device E. Lid ( Top Cover ) Rests On Water Seal Arrangement To Prevent Vapor Loss Through Top Cover And Fastened To The Still By 4 Numbers Of Eye Bolts And Fly Nuts F. Height Of Water Sealed Neck 175 Mm G. Lid ( Top Cover ) Wilt Goose Neck Arrangements From The Centre Will Be Connected To Condenser H. Air Tight Locking System Will Be Made Between Evaporator And Distillation Vessel I. Latest Incoming Steam Distribution Technology With 48 Od S.S. 304 Pipes, Along With Sufficient Numbers J. Optimum And Uniform Steam Distribution System With Three Sides Steam Distribution Holes K. Grass Nett To Be Fabricated From 304 Ss Rod Upon The Optimum Steam Distribution Gap L. The Still Will Be Engineeredwith Tilting Devices For Discharging With Necessary 10 / 16 Teeth M.S. Gear Drive ( Bevel Pinions ) And 30 Teeth C.I. Tilting Wheel With Worm M. 16 Nos. Of M.S. Angular Supports For Strengthen Of Still For Tilting With Support Of Three Nos. Outer M.S. Flat Iron Rings N. Lid ( Top Cover ) Will Have Goose Neck Arrangement From The Centre To Be Connected To Condenser O. Air Tight Locking Mechanism With Neutral Rubbers ‘O’ Ring Between Water Heater And Distillation Still Still Will Be Designed For Optimum, Rapid And Uniform Distribution Of Steam. ) ( 1 No. ) , Condensser ( Dia 250 Mmx 1250 Mmheight ) ( A. Shell & Tube Type Heat Exchanger, Complete S.S. 304 B. Baffles In Side The Shell C. Outlet Temperature Less Than 35 Degree C D. 30 Nos. 1200 Mm Length, 16 Od, 1.6 Mm Thick S.S. 304 Vertical Tubes Will Be Used E. All Contact Parts Will Bes.S. 304 With 1.6 Mm Thick Outer Shell F. 4 Nos. 33 Od Mild Steel Pipes Legs ) ( 1 No. ) , Oil Separator ( Height 350 Mm X Dia 250 Mm ) ( A. Oil Separator Will Contain Double Chamber, Made From S.S. 304 Sheet Of1.5 Mm Thick B. Dual Oil Separation System C. Volumetric Capacity 15 Liters. ) ( 1 No. ) , Water Heater ( Hydraulically Tested ) With Insullation ( Rectangular Type Evaporator To Be Fabricate From 5 Mm M.S Plate With Two Pass Heating Arrangement For Maximum Use Of Heat With 3 Nos. Flue Boxes / Pipes For Boiling Of Water. The Water Heater Will Be Insulated By Glass Wool / Mineral Wool / Woolen Sheet, Chicken Mesh And Aluminum Sheet The Volumetric Capacity Of Water Heater Will Be 220 Liters And It Will Be Installed On Rcc Furnace. L-1143 X H- 435 X B- 762 Water Boiling Area L-1625 X H- 455X B- 1250 Total Heating Area A. Inside Of Combustion Chamber Will Be Insulated With Fire Bricks And Fire Clay B. Box Type M.S. Water Heater Made From 5 Mm Plate With Insulation, Having Suitable Seventeen ( 17 Nos. ) Numbers Of Flue Tubes Inside The Tank. Furnace Will Be Connected With 6 Mtrs Height M.S. Chimney With M.S. Smoke Duct For Exit Of Flue Gas Emission C. Fire Tube / Boxes:-3 Nos. Rectangular Boxes L-930 Mm X B-200Mm X H-75Mm D. Water Heater Will Be Fabricated By 5 Mm Thick M.S. Plate E. Chimney And Smoke Duct Will Be Fabricated By 2.5 Mm Thick M.S. Sheet ) ( 1 No. ) , M.S. Chimney ( To Be Fabricated In Two Pieces From 2.5 Mm Sheet Three Ends Welded Withflat Iron Rings One Welded Withbase Plate And 2.5 Mm Top Cap Sizes:- Dia-250 Mm Height- 4750 Mm Base Plate Size 450 Mm X 450 Mm Thickness 5Mm Foundation Bolts Made From 16 Mm Rod Length 350Mm ) ( 1 No. ) , M.S.Smoke Duct ( Fabricated In Rectangular Shape Flat Iron Flanges In Both Ends Sizes:- B- 300 X H- 150 X L-2500 Mm ( 2.5 Mm, M.S. Sheet ) ( 1 No. ) , ( Fire Bricks ( 40 Pcs Standard Fire Bricks With Fire Clay, Salt And Jiggery To Construct Furnish ) ( 1 No. ) . Last date of submission for this tender is 2022-03-30. This is a Woolens tender in Pasighat, Arunachal Pradesh